C4.4 and C6.6 Engines Caterpillar


Acceleration Is Poor or Throttle Response Is Poor

Usage:

C4.4 448

Probable Causes

  • Diagnostic codes

  • Parameters in the Electronic Control Module (ECM)

  • Throttle Signal

  • Air intake and exhaust system

  • Turbocharger or turbochargers

  • Fuel supply

  • Valve lash

  • Low compression (cylinder pressure)

  • Electronic unit injectors

  • Individual malfunctioning cylinder

Recommended Actions


NOTICE

Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.


Note: The procedures have been listed in order of probability. Complete the procedures in order.

Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.

Table 1
Troubleshooting Test Steps  Values  Results 

1. Diagnostic Codes

Note: Certain diagnostic codes and/or event codes may cause poor performance. Refer to in the electronic service tool.

A. Use the electronic service tool to check for active or logged codes.
B. Use the electronic service tool to check the histogram information if the engine has been derated.

Note: If the histograms contain engine derates and no diagnostic codes are present, then the engine is operating normally.
 

Engine Derate or Diagnostic Codes
 

Result: A diagnostic code is present.

Repair: Troubleshoot the code and then reset the histogram.

Result: A diagnostic code is not present.
Proceed to Test Step 2.
 

2. Parameters in the Electronic Control Module (ECM)

A. Use the electronic service tool to verify that the correct parameters are being used. Refer to Troubleshooting, "Configuration Parameters" for additional information.
 

Parameters
 

Result: The parameters are not correct.

Repair: Input the correct parameters. Refer to Troubleshooting, "Configuration Parameters" for additional information.

Result: The parameters are correct.

Proceed to Test Step 3.
 

3. Throttle Signal

A. Monitor the status for "Throttle Position" on the electronic service tool. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
 

Throttle signal
 

Result: The throttle signal is stable.

Proceed to Test Step 4.

Result: The throttle signal is not stable.

Repair: Make the necessary repairs, Refer to the appropriate circuit test for the type of speed control that is installed.
 

4. Air Intake and Exhaust System

A. Observe the check engine lamp. Check for an air filter restriction indicator, if equipped. Replace a plugged air filters. Refer to the Operation and Maintenance Manual.

B. Check the air inlet and exhaust system for restrictions and/or leaks.
 

Restrictions
 

Result: There are restrictions in the air inlet or exhaust system.

Repair: Make the necessary repairs, Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System - Inspect" for additional information.

Result: There are no restrictions in the air inlet or exhaust system.

For engines with a single turbocharger, proceed to Test Step 5.
For engines with two turbochargers, proceed to Test Step 6.
 

5. Turbocharger

This Test Step is applicable to engines with a single turbocharger.

Note: The turbocharger that is installed on the engine is a nonserviceable item. If any mechanical fault exists, then the faulty turbocharger must be replaced.

A. Ensure that the mounting bolts for the turbocharger are tight.

B. Check that the oil drain for the turbocharger is not blocked or restricted.

C. Check that the compressor housing for the turbocharger is free of dirt and debris. Make sure that the housing is not damaged.

D. Check that the turbine housing for the turbocharger is free of dirt and debris. Make sure that the housing is not damaged.

E. Check that the turbine blades rotate freely in the turbocharger.

F. Ensure that the wastegate on the turbocharger is adjusted correctly. Refer to Systems Operation, Testing, and Adjusting, "Turbocharger - Inspect". If the wastegate actuator is faulty, replace the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install".
 

Turbocharger
 

Result: There is a fault on the turbocharger.

Repair: Repair the turbocharger or replace the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install".

Result: The turbocharger is OK.

Proceed to Test Step 7.
 

6. Turbochargers

This Test Step is applicable to engines with twin turbochargers.

Note: The turbochargers that are installed on the engine are nonserviceable items. If any mechanical fault exists, then the faulty turbocharger must be replaced.

A. Ensure that the mounting bolts for the turbochargers are tight.

B. Check that the oil drains for the turbochargers are not blocked or restricted.

C. Check that the compressor housings for the turbochargers are free of dirt and debris. Make sure that the housings are not damaged.

D. Check that the turbine housings for the turbochargers are free of dirt and debris. Make sure that the housings are not damaged.

E. Check that the turbine blades rotate freely in the turbochargers.

F. Ensure that the wastegate on the high-pressure turbocharger is adjusted correctly. Refer to Systems Operation, Testing, and Adjusting, "Turbocharger - Inspect". If the wastegate actuator is faulty, replace the high-pressure turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install".
 

Turbochargers
 

Result: There is a fault on one of the turbochargers.

Repair: Repair the faulty turbocharger or replace the faulty turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install".

Result: The turbochargers are OK.

Proceed to Test Step 7.
 

7. Fuel Supply

A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.

B. Ensure that the vent in the fuel cap is not filled with debris.

C. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.

D. If the temperature is below 0 °C (32 °F), check for solidified fuel (wax).

E. Check the primary filter/water separator for water in the fuel.

F. Check for fuel supply lines that are restricted.

G. Check that the low-pressure fuel lines are tight and secured properly.

H. Check that the Electric Fuel Lift Pump (EFLP) is operating. If the EFLP is suspect, refer to Troubleshooting, "Fuel Transfer Pump - Test".

I. Replace the in-line fuel filter that is upstream of the primary fuel filter.

J. Replace the primary and secondary fuel filters.

K. Check the diesel fuel for contamination. Refer to Systems Operation, Testing, and Adjusting, "Fuel Quality - Test".

L. Check for air in the fuel system. Refer to Systems Operation, Testing, and Adjusting, "Air in Fuel - Test".

M. Ensure that the fuel system has been primed. Refer to Systems Operation, Testing, and Adjusting, "Fuel System - Prime".
 

Fuel system
 

Result: The fuel supply is not OK.

Repair: Repair the fuel system or replace the fuel system components, as necessary.

Result: The fuel supply is OK.

Proceed to Test Step 8.
 


Illustration 1g03700009
Transfer Pump Inlet Regulator (TPIR) components on a C4.4 engine
(1) Transfer Pump Inlet Regulator (TPIR)
(2) TPIR return port


Illustration 2g06100802
Transfer Pump Inlet Regulator (TPIR) components on a C6.6 engine
(1) Transfer Pump Inlet Regulator (TPIR)
(2) TPIR return port


Illustration 3g02485896
Minimum TPIR flow rate for a C4.4 engine in a 12 VDC system


Illustration 4g02485897
Minimum TPIR flow rate for a C4.4 engine in a 24 VDC system


Illustration 5g02355128
Minimum TPIR flow rate for a C6.6 engine in a 12 VDC system


Illustration 6g02355130
Minimum TPIR flow rate for a C6.6 engine in a 24 VDC system

Table 2
Troubleshooting Test Steps  Values  Results 

8. Transfer Pump Inlet Regulator (TPIR) Flow Test

For a C4.4 engine, refer to Illustration 1. For a C6.6 engine, refer to Illustration 2.

A. Disconnect the TPIR return line from the drain port on the TPIR. Install a suitable blanking cap on the open port in the TPIR return line.

B. Connect a temporary drain line to the drain port on the TPIR.

C. Place the end of the temporary drain line into a suitable calibrated container.

D. With the isolator switch in the ON position but the engine not running, use a suitable multimeter to measure the input voltage to the EFLP. Record the reading.

E. With the isolator switch in the ON position but the engine not running, measure the fuel flow from the temporary drain line.

F. Refer to Illustration 3 through 6 for the minimum acceptable flow rate.

G. Remove the temporary drain line from the drain port on the TPIR. Connect the TPIR return line to the TPIR.
 

TPIR flow rate
 

Result: The fuel flow is greater than the minimum limit.

Proceed to Test Step 10.

Result: The fuel flow is less than the minimum limit.

Proceed to Test Step 9.
 


Illustration 7g02527498
Minimum EFLP flow rate in a 12 VDC system


Illustration 8g02527518
Minimum EFLP flow rate in a 24 VDC system

Table 3
Troubleshooting Test Steps  Values  Results 

9. EFLP Flow Test at the Primary Fuel Filter Inlet

A. Make sure the keyswitch is in the OFF position.

B. Disconnect the fuel inlet connection from the primary fuel filter head.

C. Install a suitable blank on the fuel inlet port on the primary fuel filter head.

D. Place the open end of the fuel inlet line in a suitable calibrated container.

E. With the keyswitch in the ON position, measure the input voltage at the EFLP. Record the result.

F. With the keyswitch in the ON position, measure the flow from the fuel inlet line. Record the result.

G. Check the recorded voltage and fuel flow on the graph in Illustration 7 or 8.
 

EFLP flow
 

Result: The fuel flow is below the minimum value for the recorded voltage.

Repair: Replace the EFLP. Refer to Disassembly and Assembly, "Fuel Priming Pump - Remove and Install".

Result: The fuel flow is above the minimum value for the recorded voltage.

Proceed to Test Step 10.
 

10. Check the Return Fuel Lines

A. Make sure that the TPIR return line is not blocked or kinked.

B. If the TPIR return line is clear, confirm that the Electric Fuel Lift Pump (EFLP) is operating. Make sure that fuel lines between the EFLP and the TPIR are not blocked or kinked.
 

Return lines
 

Result: The TPIR return line or the fuel lines between the EFLP and the TPIR are blocked or kinked.

Repair: Clear or replace the blocked line.

Result: The TPIR return line and the fuel lines between the EFLP and the TPIR are clear.

Repair: Replace the EFLP.

If the fault is still present, proceed to Test Step 11.
 

11. Valve Lash

Note: The valve lash can affect the performance of the engine.
A. Check the valve lash.
 

Valve lash
 

Result: The valve lash is not correct.

Repair: Check the valve lash. Refer to Systems Operation, Testing, and Adjusting, "Engine Valve Lash - Inspect" for the correct procedure.

Result: The valve lash is correct.

Proceed to Test Step 12.
 

12. Low Compression (Cylinder Pressure)

A. Perform a compression test. Refer to Systems Operation, Testing, and Adjusting, "Compression - Test".
 

Cylinder compression
 

Result: The results of the compression test are outside the specifications.

Repair: Investigate the cause and rectify any faults.

Note: Possible causes of low compression are shown in the following list:

· Loose glow plugs
· Faulty piston
· Faulty piston rings
· Worn cylinder bores
· Worn valves
· Faulty cylinder head gasket
· Damaged cylinder head

Result: The results of the compression test are OK.

Proceed to Test Step 13.
 

13. Electronic Unit Injectors

A. Use the electronic service tool to perform the automatic "Cylinder Cut Out Test".

Note: If the compression test that was performed in Test Step 12 was satisfactory, the "Cylinder Cut Out Test" will identify any faulty injectors.
 

Electronic Unit Injectors
 

Result: A faulty injector is indicated.

Repair: Remove any faulty electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".

Install new electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".

Repeat the automatic "Cylinder Cut Out Test". If the fault is still apparent, remove the replacement electronic unit injector and install the original electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and Disassembly and Assembly, "Electronic Unit Injector - Install".

Result: All injectors are OK.

Proceed to Test Step 14.
 

14. Individual Malfunctioning Cylinders

A. With the engine speed at a fast idle, use the electronic service tool to perform the manual "Cylinder Cut Out Test".

As each cylinder is cut out, listen for a change in the sound from the engine. When a cylinder is cut out, there should be a noticeable change in the sound of the engine.

If a change in the sound of the engine is not noted, the isolated cylinder is not operating under normal conditions. If the isolation of a cylinder results in a change in the sound that is less noticeable, the cylinder may be operating below normal performance.
 

Cylinders
 

Result: The test indicates a faulty cylinder.

Repair: Investigate the cause of the fault on any cylinder that is not operating. Investigate the cause of the fault on any cylinder that is operating below normal performance.

Result: The test indicates that all cylinders are OK.

Contact the Dealer Solutions Network (DSN).
 

Caterpillar Information System:

Product Evaluation Report - AFA Bad Report {0374, 1000} Product Evaluation Report - AFA Bad Report {0374, 1000}
C4.4 and C6.6 Engines Event Codes
C4.4 and C6.6 Engines Electrical Connectors
A New Alternator Guard Is Used on Certain G3500 Engines {7174} A New Alternator Guard Is Used on Certain G3500 Engines {7174}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Diesel Particulate Filter Regeneration Does Not Occur
794 AC Off-Highway Truck High Voltage Components - Check
New Solenoid Valve for Certain Gas Engines {5479} New Solenoid Valve for Certain Gas Engines {5479}
C175 Tier 4 Final Engines for Off-Highway Trucks DEF Pressure Is High
C7.1 Marine Propulsion Engine Belts - Inspect/Adjust/Replace
794 AC Off-Highway Truck Rear Wheel Spindle Fasteners - Replace
794 AC Off-Highway Truck Rear Wheel Spindle Fasteners - Inspect
® Marine Display Display
DE Series Generator Set with Cat C1.1, C1.5, and C2.2 Engines Safety Messages
C7.1 Marine Engine Engine Oil Pressure Sensor - Remove and Install
C175 Tier 4 Final Engines for Off-Highway Trucks DEF Pump Motor - Test
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Engine Misfires, Runs Rough or Is Unstable
HPU300 Hydraulic Power Pack Power Pack Connection and Coupling
C4.4 and C6.6 Engines Alternator Problem
C7.1 Marine Engine Fuel Pressure Sensor - Remove and Install
C9.3 Marine Propulsion Engine Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.1/4.2 If equipped
C7.1 Marine Engine Coolant Temperature Sensor - Remove and Install
G3606 and G3608 Engines Maintenance Interval Schedule - Natural Gas Engines That Have a Compression Ratio of 10.5:1 or 11:1
G3606 and G3608 Engines Maintenance Interval Schedule - Engines That Use Bio-Gas
G3606 and G3608 Engines Maintenance Interval Schedule - Wellhead or Natural Gas Engines That Have a 9.2:1 Compression Ratio
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.