Electrical Connectors
Connectors for the Electronic Control Module (ECM)
The Electronic Control Module (ECM) uses connectors that have 70 terminals to interface to the wiring harness.
Show/hide table
| |
| Illustration 1 | g01877659 |
|
Layout of the Connector Pins (view from the rear) | |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 151-6320 | Removal Tool (Red) | 1 |
Show/hide table
| |
| Illustration 2 | g01877813 |
|
Removal Tool | |
- Remove the connector from the ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
- Position Tooling (A) around wire (2).
Note: Make sure that the tool stays perpendicular to the face of connector (1).
- Push the tool into the hole for the terminal. Gently pull the wire to remove the terminal from the rear of connector (1).
- Remove the Tooling (A) from the wire.
Note: If a terminal must be replaced, part number 9X-3402 must be used for 16 and 18 AWG wire. Part number 126-1768 must be used for 14 AWG wire.
- Push the terminal into the rear of connector (1) until the terminal engages with the locking device.
- Gently pull on wire (2) to make sure that the terminal is retained by the locking device.
- Connect the connector to the ECM and then tighten the retaining screw to a torque of
6 N·m (53 lb in) .
Show/hide table
| |
| Illustration 3 | g06099709 |
Analog Sensor Connector (active)
Show/hide table
| |
| Illustration 4 | g01240891 |
Analog Sensor Connector (passive)
Show/hide table
| |
| Illustration 5 | g01241538 |
Connectors for the Termination Resistor
Show/hide table
| |
| Illustration 6 | g01355248 |
Show/hide table
| |
| Illustration 7 | g01155187 |
Show/hide table
| |
| Illustration 8 | g02219254 |
Show/hide table
| |
| Illustration 9 | g02220494 |
Caterpillar Information System:
A New Alternator Guard Is Used on Certain G3500 Engines {7174} A New Alternator Guard Is Used on Certain G3500 Engines {7174}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Diesel Particulate Filter Regeneration Does Not Occur
794 AC Off-Highway Truck High Voltage Components - Check
New Solenoid Valve for Certain Gas Engines {5479} New Solenoid Valve for Certain Gas Engines {5479}
C175 Tier 4 Final Engines for Off-Highway Trucks DEF Pressure Is High
C7.1 Marine Propulsion Engine Belts - Inspect/Adjust/Replace
794 AC Off-Highway Truck Rear Wheel Spindle Fasteners - Replace
794 AC Off-Highway Truck Rear Wheel Spindle Fasteners - Inspect
® Marine Display Display
Reference Guide for a Proper Failure Analysis by CAT Dealer {0374, 1000} Reference Guide for a Proper Failure Analysis by CAT Dealer {0374, 1000}
New Engine Software Is Now Used For Certain G3512 Engines {7610, 7620} New Engine Software Is Now Used For Certain G3512 Engines {7610, 7620}
Securing the C4.4 Generator Set for Transportation {7274} Securing the C4.4 Generator Set for Transportation {7274}
C4.4 and C6.6 Engines Event Codes
Product Evaluation Report - AFA Bad Report {0374, 1000} Product Evaluation Report - AFA Bad Report {0374, 1000}
C4.4 and C6.6 Engines Acceleration Is Poor or Throttle Response Is Poor
DE Series Generator Set with Cat C1.1, C1.5, and C2.2 Engines Safety Messages
C7.1 Marine Engine Engine Oil Pressure Sensor - Remove and Install
C175 Tier 4 Final Engines for Off-Highway Trucks DEF Pump Motor - Test
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Engine Misfires, Runs Rough or Is Unstable
HPU300 Hydraulic Power Pack Power Pack Connection and Coupling
C4.4 and C6.6 Engines Alternator Problem
C7.1 Marine Engine Fuel Pressure Sensor - Remove and Install
C9.3 Marine Propulsion Engine Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.1/4.2 If equipped
C7.1 Marine Engine Coolant Temperature Sensor - Remove and Install