Hydraulic Oil Filter - Replace
Show/hide table
 |
|
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin. |
- Place the power pack on firm, level, and horizontal ground.
- Remove cover (A).
- Unscrew breather filter (B) slowly to release the pressure inside the reservoir slowly.
- Thoroughly clean the outside of hydraulic oil filter (C).
- Place a suitable container under the power pack to collect the hydraulic oil as it flows out.
Show/hide table
Illustration 2 g06098548 - Unscrew cap (D) of the hydraulic oil filter.
- Collect the hydraulic oil as it drains.
Note: Refer to "General Hazard Information" for information that pertains to containing fluid spillage.
- Remove spring (E) if it is not seated on cover (D).
- Remove the old filter element (F) by lifting out the element with the handle and replace with a new element.
- Check the surface of the element for dirt residues and coarse particles.
Note: Coarse particles can be a sign of damage to the components.
- Clean the drip and dirt collector (G).
- Carefully place a new filter element onto the mount in the filter housing.
- Remove dirt from the housing and the sealing surface of cover (D) if necessary.
- Screw on cap (D) with spring (E) and tighten by hand.
- Install and tighten breather filter (B).
- Operate the power pack and check for leaks.
- Install the cover.
- Dispose of used filters and used fluids according to local regulations.
Show/hide table
| |
| Illustration 1 | g06098525 |
Caterpillar Information System:
C4.4 and C6.6 Engines Diagnostic Trouble Codes
ECPC Valves May Fail on Cat Transmission Systems {3073, 3139, 3167} ECPC Valves May Fail on Cat Transmission Systems {3073, 3139, 3167}
349F and 352F Excavators Machine System Specifications Swing Drive - Left Swing Drive and Right Swing Drive
C175-16 and C175-20 Locomotive Engines Fuel Pump (High Pressure) - Remove and Install
C175-16 and C175-20 Locomotive Engines Air Inlet Manifold - Remove and Install
Front Suspension Failures May Occur on Certain 777D/777F/777G Off-Highway Trucks {7200, 7201, 7551} Front Suspension Failures May Occur on Certain 777D/777F/777G Off-Highway Trucks {7200, 7201, 7551}
C175-16 and C175-20 Locomotive Engines Valve Lifter - Install
C175 Tier 4 Final Engines for Off-Highway Trucks DEF Pressure Does Not Respond
M0074040: 509-5085 Lifting Tool Assembly {0374, 0599, 0629, 0632, 3023, 3159, 3160, 5363, 7000} M0074040: 509-5085 Lifting Tool Assembly {0374, 0599, 0629, 0632, 3023, 3159, 3160, 5363, 7000}
C12.9 Marine Engines Crankshaft Front Seal - Remove and Install
New Basic Engine Components Are Used in C175-16 Engines {1202, 1205} New Basic Engine Components Are Used in C175-16 Engines {1202, 1205}
A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Machine Engines {1207} A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Machine Engines {1207}
A New Cylinder Liner Assembly And Piston Is Now Used For Certain 3516 Locomotive Engines {1201, 1216} A New Cylinder Liner Assembly And Piston Is Now Used For Certain 3516 Locomotive Engines {1201, 1216}
Failure Analysis Report - AFA Good Report {0374, 1000} Failure Analysis Report - AFA Good Report {0374, 1000}
C4.4 and C6.6 Engines General Information
C4.4 and C6.6 Engines Welding Precaution
C4.4 and C6.6 Engines Component Location
PM820, PM822, and PM825 Cold Planer Machine Systems Conveyor Belt (Second Stage) - Remove and Install
G3512 Generator Set Engines Manifold Air Pressure Sensor
G3512 Generator Set Engines Measuring Inlet Manifold Temperature
G3512 Generator Set Engines Restriction of Air Inlet and Exhaust
HPU300 Hydraulic Power Pack Before Starting Motor
G3612 and G3616 Engines Maintenance Interval Schedule - Engines With 10.5 or 11.1 Compression Ratio and Use Natural Gas
G3612 and G3616 Engines Maintenance Interval Schedule - Bio-Gas Engines