Swing Drive - Left Swing Drive and Right Swing Drive
Show/hide table
Illustration 1 | g06098288 |
Typical example |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
A | - | - | After installation of four spring pins (1), create two stake marks lightly at a distance (A) from each spring pin. |
Distance from edge of the spring pin hole to the stake mark |
|||
2 | - | - | Apply sealant to the surfaces of the housing cover and the ring gear before assembly. |
3 | 1 | 6V-7238 Shutoff Valve | Torque for installing the shutoff valve |
Torque for shutting off the shutoff valve |
|||
4 | 1 | Nut | Torque to |
5 | 1 | 096-4339 Roller Bearing As | Before assembly, applyLoctite C5A copper anti-seize to the outer diameter and the inner diameter of the mating parts of the roller bearings. |
6 | 1 | 095-1806 Roller Bearing | Before assembly, applyLoctite C5A copper anti-seize to the outer diameter and the inner diameter of the mating parts of the roller bearings. |
7 | 2 | 135-9044 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. |
Show/hide table
Illustration 2 | g06098290 |
View C-C |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
8 | 2 | Connector | Torque to |
Torque to |
|||
9 | 1 | 114-1399 Gauge Pipe | Torque to |
Torque to |
|||
10 | - | Bolt | Torque to |
Torque to |
|||
11 | 30 | 095-0670 Bolt | Torque to |
Show/hide table
(1) | For 296-6253, 418-7155 and 470-0474. |
(2) | For 296-6250. |
(3) | For 418-7155 and 470-0474. |
(4) | For 296-6250 and 296-6253. |
Caterpillar Information System:
C175-16 and C175-20 Locomotive Engines Fuel Pump (High Pressure) - Remove and Install
C175-16 and C175-20 Locomotive Engines Air Inlet Manifold - Remove and Install
Front Suspension Failures May Occur on Certain 777D/777F/777G Off-Highway Trucks {7200, 7201, 7551} Front Suspension Failures May Occur on Certain 777D/777F/777G Off-Highway Trucks {7200, 7201, 7551}
C175-16 and C175-20 Locomotive Engines Valve Lifter - Install
C175 Tier 4 Final Engines for Off-Highway Trucks DEF Pressure Does Not Respond
M0074040: 509-5085 Lifting Tool Assembly {0374, 0599, 0629, 0632, 3023, 3159, 3160, 5363, 7000} M0074040: 509-5085 Lifting Tool Assembly {0374, 0599, 0629, 0632, 3023, 3159, 3160, 5363, 7000}
C12.9 Marine Engines Crankshaft Front Seal - Remove and Install
New Basic Engine Components Are Used in C175-16 Engines {1202, 1205} New Basic Engine Components Are Used in C175-16 Engines {1202, 1205}
A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Machine Engines {1207} A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Machine Engines {1207}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620} New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
Identifying Oil Pumps on Certain C27, C32, and 3412 Engines {1304} Identifying Oil Pumps on Certain C27, C32, and 3412 Engines {1304}
HPU300 Hydraulic Power Pack Daily Inspection
ECPC Valves May Fail on Cat Transmission Systems {3073, 3139, 3167} ECPC Valves May Fail on Cat Transmission Systems {3073, 3139, 3167}
C4.4 and C6.6 Engines Diagnostic Trouble Codes
HPU300 Hydraulic Power Pack Hydraulic Oil Filter - Replace
A New Cylinder Liner Assembly And Piston Is Now Used For Certain 3516 Locomotive Engines {1201, 1216} A New Cylinder Liner Assembly And Piston Is Now Used For Certain 3516 Locomotive Engines {1201, 1216}
Failure Analysis Report - AFA Good Report {0374, 1000} Failure Analysis Report - AFA Good Report {0374, 1000}
C4.4 and C6.6 Engines General Information
C4.4 and C6.6 Engines Welding Precaution
C4.4 and C6.6 Engines Component Location
PM820, PM822, and PM825 Cold Planer Machine Systems Conveyor Belt (Second Stage) - Remove and Install
G3512 Generator Set Engines Manifold Air Pressure Sensor
G3512 Generator Set Engines Measuring Inlet Manifold Temperature
G3512 Generator Set Engines Restriction of Air Inlet and Exhaust