Gear Group (Rear)
Show/hide table
| |
| Illustration 1 | g06059802 |
Show/hide table
| |
| Illustration 2 | g06059803 |
Show/hide table
| |
| Illustration 3 | g06059804 |
Show/hide table
| Specification for 467-7815 Rear Gear Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| 1 | 2 | 156-9744 Camshaft Drive Gear | Before assembly, clean the taper of the camshaft and the tapered bore of the camshaft drive gear with lint free cloth saturated with cleaning solvent to remove excess oil. Clean with alcohol wipe. |
| 2 | 2 | 443-6069 Idler Gear As | After installation, bore of 125-9751 Bushing in the idler gear assembly is Installation depth of the bushing is |
| 3 | 2 | 101-1368 Thrust Washer | Thickness of the new thrust washer is |
| 4 | 1 | 443-9634 Idler Gear As | After installation, bore of 101-1372 Bushing in the gear assembly is Installation depth of the bushing is |
| 5 | 4 | 8M-2530 Bolt | Torque to |
| 6 | 1 | 442-2324 Gear Shaft | Diameter is |
| 7 | 2 | 9X-8887 Bolt | Use the following procedure to tighten the bolt for the camshaft drive gears: 1. Tighten the bolt for the camshaft drive gear to 2. Mark a vertical line on the head of the bolt for the camshaft drive gear. Refer to Illustration 2. 3. Place a driver against the retaining plate of the camshaft drive gear. Strike the driver solidly with a hammer 3 to 4 times. 4. Again, tighten the bolt for the camshaft drive gear to 5. Repeat steps 3 and 4 until the mark on the bolt turns a minimum of 90 degrees. Refer to Illustration 3. |
| 8 | 4 | 1B-4367 Bolt | Torque to |
| 9 | 2 | 8S-2331 Bolt | Torque to |
| 10 | 1 | 101-1365 Thrust Plate | Thickness of the new thrust plate is |
| 11 | 1 | 399-7361 Crankshaft Gear | The mark on the gear assembly (4) must be in alignment with the mark on the crankshaft gear (11). |
| 12 | 2 | 101-1367 Idler Shaft | Diameter is |
Caterpillar Information System:
Cat® Detect Object Detection System Display Module - Flash Program
Cat® Detect Object Detection System Object Detection Sensor - Adjust
Cat® Detect Object Detection System Diagnostic Code List
Cat® Detect Object Detection System Event Codes
Cat® Detect Object Detection System Operational Problems
C175-16 and C175-20 Locomotive Engines Electronic Control Module (Engine) - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines General Information
G3512 Generator Set Engines Ignition Primary - Test
New Fuel Filter Base Isolation Mounts Are Now Available For Certain C13 Engines {1262} New Fuel Filter Base Isolation Mounts Are Now Available For Certain C13 Engines {1262}
An Improved Connecting Rod Bolt Is Now Used for Certain C11 and C13 Engines {1225} An Improved Connecting Rod Bolt Is Now Used for Certain C11 and C13 Engines {1225}
Aluminum Charge Air Cover Replacement Procedure for Certain C18 Engines {1052, 1061, 1379} Aluminum Charge Air Cover Replacement Procedure for Certain C18 Engines {1052, 1061, 1379}
Aluminum Charge Air Cover and Exhaust Gas Cooler Replacement Procedure for Certain C18 Engines {1052, 1061, 1379} Aluminum Charge Air Cover and Exhaust Gas Cooler Replacement Procedure for Certain C18 Engines {1052, 1061, 1379}
DE Series Generator Sets With Cat C3.3 Engine Product Description
C280 Marine Engines SCR Catalyst Temperature Sensor - Test
C175-16 and C175-20 Locomotive Engines Crankshaft - Remove
C175-16 and C175-20 Locomotive Engines Camshaft - Remove
3512E Engines Accumulator (Fuel Injection) - Remove and Install
A New Wastegate Bellows Assembly Is Used for Certain 3512C Heavy-Duty Locomotive Engines {1059} A New Wastegate Bellows Assembly Is Used for Certain 3512C Heavy-Duty Locomotive Engines {1059}
3512E Engines Fuel Manifold - Remove and Install
PM820, PM822, and PM825 Cold Planer Machine Systems Hood - Remove and Install - Left
C175-16 Locomotive Engine Air Inlet Piping - Inspect
Selective Catalytic Reduction Retrofit Aftertreatment Exhaust Temperature Is Low
C11, C13, C15, and C18 Industrial Engines Electrical Power Supply - Test
C175-16 and C175-20 Locomotive Engines Aftercooler - Remove and Install