Cylinder Head - Install - For EAME use only
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 301-5215 | 张紧器总成(1) | 4 |
191-5333 | 支撑组件 | 4 | |
B | 191-5347 | 液压泵 (空气) | 1 |
229-9453 | 附件总成 (油泵) | 1 | |
C | 126-6918 | 提升支架 | 1 |
D(2) | 225-5637 | 支架 | 2 |
225-5636 | 齿座 | 2 |
Show/hide table
(1) | 191-5322 缸盖总成用于缸盖。 |
(2) | 工具 ( D) 可用在 3612 和 3616 柴油发动机前缸盖上的前螺柱上。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将 O 形密封圈 (13) 安装至适配器 (15 )上。
- 将适配器 ( 15 )安装至密封板 (18 )和密封板 (19) 上。
- 将 O 形密封圈 (17) 安装至密封板 (18) 和密封板 (19) 上。
- 将 O 形密封圈 (16) 安装至密封板 (19) 上。
- 将 O 形密封圈 (14) 安装至密封板 (18) 上。
- 将密封板 ( 18) 和密封板 ( 19) 安装至缸体。
- 将垫片 (12 )安装至缸套。
Show/hide table
图 2 g03890554 - 将工具 (C )和适当的起吊设备连接至缸盖 (11),然后将缸盖 (11 )定位至发动机上。 缸盖 (11) 的重量约为
204 kg (450 lb) 。Show/hide table图 3 g01108551 - 将缸盖螺母 (11B) 安装至锥形螺柱 ( 11A)。
Show/hide table
图 4 g01108449 - 将工具 ( A )安装至锥形螺柱 (11A)。 当锥形螺柱 (11A) 上的工具 (A) 过紧时,将工具 (A) 回旋 1/4 圈。
Show/hide table
图 5 g01108451 - 将工具 (B) 安装至工具 (A)。
Show/hide table
图 6 g01108543 - 固定工具 (B) 以实现
125000 ± 4920 kPa (18130 ± 715 psi) 。 对工具 (A )施压时,手动拧紧缸盖螺母 (11B)。 请参阅发动机信息, "SEBD9405 3600、C280 和 G3600 发动机螺柱张紧工具总成要求不同液压压力"。释放工具 (B) 上的压力。 重置工具 (B) 上的压力,以实现
125000 ± 4920 kPa (18130 ± 715 psi) 。 对工具 (A )施压时,手动拧紧缸盖螺母 (11B)。 最后一次释放工具 (B) 上的压力。卸下工具 (A) 和工具 (B)。
注: 对工具 (A) 施压时,如果红色标记 (X) 暴露在外,那么工具 (A) 处于最大行程。 释放工具 (B) 的压力,然后重复步骤 10 至 12。 未能释放压力可能会导致工具 ( A) 损坏,或不能正确拧紧缸盖螺母 (11B)。
Show/hide table图 7 g01108448 - 安装进气阀 ( 10)。 安装螺栓 (9)。
Show/hide table
图 8 g00926568 - 安装管路组件 (8)。
Show/hide table
图 9 g03890523 - 安装盖组件 (7)。 安装扩展组件 (6)。
Show/hide table
图 10 g03890314 - 安装变压器 (5)。
- 安装管组件 (4)。
- 连接线束组件 (3)。
Show/hide table
图 11 g03890307 - 连接管组件 (2)。 安装线束组件 (1)。
- 重新加注冷却系统。
- 接通发动机供油。
Show/hide table
图 1 | g01108492 |
结束:
- 安装适当的排气歧管。 请参阅拆解和组装, "排气歧管 - 拆卸和安装"。
- 安装摇臂。 请参阅拆解和装配摇臂, " - 安装"。
Caterpillar Information System:
Energy Storage System Battery Management Unit - Replace
Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000} Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
C1.7 and C2.2 Industrial Engines Exhaust Gas Recirculation Valve - Clean
Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000} Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000} Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
EMCP4.2B Custom Text String Is Not Shown
EMCP4.2B Diagnostic Trouble Code List
EMCP4.2B Analog Input Programming
EMCP4.2B Output Programming
EMCP4.2B ECM Connections
EMCP4.2B Integrated Voltage Regulator Connections
EMCP4.2B Typical Generator Abbreviations
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Turbocharger Cartridge - Remove
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Turbocharger Cartridge - Install
SRMP Electric Power Generation SRMP Generator Bearing - Remove and Install
C3.3B and C3.8 Engines for Caterpillar Built Machines DEF Concentration Is Incorrect
G3606 and G3608 Engines Crankshaft - Remove
A New Pressure Switch Is Used on Certain G3500 and G3600 Engines {7400} A New Pressure Switch Is Used on Certain G3500 and G3600 Engines {7400}
G3606 and G3608 Engines Crankshaft - Install
C15 Generator Set Maintenance Interval Schedule - Prime Power
C15 Generator Set Maintenance Interval Schedule - Standby
C15 Generator Set Maintenance Interval Schedule - Emergency Standby Power
C3.3B and C3.8 Engines for Caterpillar Built Machines DEF Module Does Not Respond
C1.7 and C2.2 Industrial Engines Engine Valve Lash - Check