UPS 250 and UPS 300 Uninterruptible Power Supplies Caterpillar


Troubleshooting

Usage:

UPS 250 APZ

------ WARNING! ------

告警:高电压能造成人身伤害或死亡。

发电设备必须在运转中进行测试和/或调节时,设备带有高电压和高电流。

不适当的测试设备可能失效,并会出现危及用户的高压电击。

应确保测试设备设计可用于,并且可准确操作于意欲进行的高电压和高电流测试。


显示窗口

表 1
显示窗口 
故障  原因  方案 
显示窗口没有显示。  对比度太淡。  按下向上箭头键以便使显示变暗。 
显示窗口为黑色。  对比度太暗。  按下向下箭头键以便使显示变淡。 

紧急断电开关

表 2
紧急断电开关 
故障  原因  方案 
按下紧急断电 (EPO) 开关之后,系统不会立即重新启动。  按下 EPO 开关时,断路器跳闸断开。  打开前门,复位紧急断电 (EPO) 开关的小断路器。 

风扇

表 3
风扇 
故障  原因  方案 
风扇被显示出现故障。
风扇配备了气流指示器。 
风扇出口堵塞。  从系统上端清除堵塞物。 
排气门没有打开。 确保这些门可以自如开关。 
风扇监测接头没有插进用于风扇监测的 印刷电路板 上。 确保风扇监测接头有效连接。 
用于风扇监测的印刷电路板的保险丝熔断。 更换跳闸的所有保险丝。 

初次启动期间真空度不稳定

表 4
初次启动期间真空度不稳定 
故障  原因  方案 
系统启动期间真空度上升。  飞轮内部产生的热量导致压力上升。 系统因此而循环通电和断电直到真空压力均衡为止。  初次启动的正常情况 

飞轮旋转

表 5
飞轮旋转 
故障  原因  方案 
转速表读数为 0,或转子转速无可察觉改变。  飞轮不在充电。  确保钥匙开关处于"在线"位置。 

显示面板

事件和告警

表 6
显示面板 
故障  原因  方案 
显示面板发出蜂鸣声。  有事件发生。  进入事件记录,以便确定发生的事件的类型。 
系统有规律地在液晶显示器 (LCD) 上显示告警。  系统正在提供警告指示,系统可能需要留意或维修。  记录经常出现的告警。 联系您的 Cat 代理商以便商讨应采取的适当的保养措施。 
告警事件:"System Waiting on Vacuum"(关于真空的系统警告)
系统丧失了部分真空度,系统刚开始运转时系统温度上升。 
冷态启动时系统飞轮壳体内可能积聚了一些水分。 随着系统逐渐升温,将会出现水分蒸发的暂时性现象。 这将导致真空压力上升。  系统运转数小时之后该告警事件应不再出现。 
告警事件:"Vacuum gauge warning: Over maximum value"(真空表警告:超过最大值) 或 "System Waiting On Vacuum"(关于真空的系统警告)  有三个可能性。 真空泵无法启动。 无法保持真空度。 真空泵运转不正常。  确保辅助交流电源向系统供电。 确保位于飞轮壳体底部的真空阀处于关闭状态。 如果有任何问题(真空泵)继续存在的话,请与 Caterpillar 维修部门联系。 
告警事件:径向或轴承轴承振动警告:超过限制值  出现了导致系统振动过度的情况或轴承本身可能需要保养。  确保系统没有被任何外力损伤。 确保振动回到轴承复位,或检查事件记录中有无其它振动告警。 使用显示终端或 UPS View(UPS 视图)来确保振动力小于 0.25g(重力)。 如果不断出现过度振动,请与 Cat 代理商维修部门联系。
 
告警事件:"__ warning. Over limit: __"(__告警。超过极限:__)  系统的遥测设定值被超出,致使警告信息出现。  请致电 Caterpillar 维修部门,商讨应采取的适当的保养措施。 

Caterpillar Information System:

UPS 250 and UPS 300 Uninterruptible Power Supplies Sight Gauge - Clean
UPS 250 and UPS 300 Uninterruptible Power Supplies Oil Level - Check
UPS 250 and UPS 300 Uninterruptible Power Supplies Oil - Change
UPS 250 and UPS 300 Uninterruptible Power Supplies Flywheel - Clean
UPS 250 and UPS 300 Uninterruptible Power Supplies DC Bus Capacitor - Replace
UPS 250 and UPS 300 Uninterruptible Power Supplies Bearing (3.5 EVD or Greater) - Replace
UPS 250 and UPS 300 Uninterruptible Power Supplies Bearing (Earlier) - Replace
UPS 250 and UPS 300 Uninterruptible Power Supplies Battery - Replace
C15 Generator Set Maintenance Interval Schedule
C7.1 Commercial Marine Engine Coolant Temperature Is High
UPS 250 and UPS 300 Uninterruptible Power Supplies Air Filter Element - Clean/Replace
UPS 250 and UPS 300 Uninterruptible Power Supplies User Interface
UPS 250 and UPS 300 Uninterruptible Power Supplies Telemetry Parameters
UPS 250 and UPS 300 Uninterruptible Power Supplies Status Messages
UPS 250 and UPS 300 Uninterruptible Power Supplies Maintenance Interval Schedule
C15 Generator Set Maintenance Interval Schedule
C15 Generator Set Maintenance Interval Schedule
C7.1 Commercial Marine Engine Crankcase Breather Ejects Oil
C7.1 Commercial Marine Engine Crankcase Fumes Disposal Tube Has Oil Draining
C27 Generator Set Maintenance Interval Schedule - Prime
C27 Generator Set Maintenance Interval Schedule - Standby
C7.1 Commercial Marine Engine Cylinder Is Noisy
C7.1 Commercial Marine Engine Electronic Service Tool Does Not Communicate
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Maintenance Interval Schedule
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.