MSS3s Machine Security System Caterpillar


ECM Software - Install

Usage:

120G 11W
Perform the following procedure to flash program the ECM. The ECM is flashed to upgrade the software. Flash programming of the ECM must also be done if the ECM has been replaced. The Caterpillar ® Electronic Technician (Cat ® ET) service tool contains the program WinFlash. WinFlash is used to load software into the ECM. The following procedure is used to flash software into the MSS3s ECM.

Procedure

  1. Connect the data-link cable between the communication adaptor and the Cat ® ET service tool.

  2. Connect the data-link cable between the communication adaptor and the diagnostic connector of the machine.

  3. Use WinFlash to load the software.

Caterpillar Information System:

740 GC, 740 Ejector, 745 Articulated Truck Power Train Differential and Bevel Gear (Front and Rear) - Remove and Install
CP44B and CS44B Vibratory Soil Compactors Machine Systems Control Valve (Leveling Blade) - Remove and Install
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Fan Guard - Remove and Install
777D and 777E Off-Highway Truck Air System and Brakes Gear Pump (Torque Converter Charging, Scavenge, and Parking Brake Release)
CW34 Pneumatic Compactor Machine Electronic Control System Diagnostic Trouble Codes
16M Series 3 and 18M Series 3 Motor Grader Machine Preparation
Installing the 484-8211 Battery Disconnect Kit {1411} Installing the 484-8211 Battery Disconnect Kit {1411}
2015/08/05 A New Pinout Configuration Has Been Approved For Use on The Water In Fuel Sensor (WIF) Harness Connector on Certain Wheel Feller Bunchers {1408, 7490, 7610, 7620}
New Pinouts For Water In Fuel Harness (WIF) Connector When New Engine Ratings Electronic Software Gp Is Installed on Certain Wheel Feller Buncher{1408, 7490, 7610, 7620} New Pinouts For Water In Fuel Harness (WIF) Connector When New Engine Ratings Electronic Software Gp Is Installed on Certain Wheel Feller Buncher{1408, 7490, 7610, 7620}
773E Off-Highway Truck Air System and Brakes Pressure Sensor (Air System)
773E Off-Highway Truck Air System and Brakes Pressure Switch (Stop Light)
773E Off-Highway Truck Air System and Brakes Solenoid Valve (Automatic Retarder Control)
MSS3s Machine Security System ECM - Replace
CW34 Pneumatic Compactor Machine Electronic Control System Determining Diagnostic Trouble Codes
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Gear Motor (Fan Drive) - Disassemble
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Gear Motor (Fan Drive) - Assemble
CW34 Pneumatic Compactor Machine Electronic Control System Emerging Symptom Information
CW34 Pneumatic Compactor Machine Electronic Control System Machine Movement Without Request
CW34 Pneumatic Compactor Machine Electronic Control System CAN Data Link - Test
CW34 Pneumatic Compactor Machine Electronic Control System Relay - Test
CW34 Pneumatic Compactor Machine Electronic Control System Solenoid Valve - Test
CW34 Pneumatic Compactor Machine Electronic Control System Sensor Supply - Test
PL72 Pipelayers Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
CW34 Pneumatic Compactor Machine Electronic Control System Sensor Signal (Analog, Passive) - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.