Rework Procedure of the Lines Routing for the Autolube on the Front Tilt Lever for Certain 966 and 972 Medium Wheel Loaders{5104, 6116, 6119, 6129, 7540} Caterpillar

Wheel Loader:

966H (S/N: A6D1-UP; RYF1-UP; A6G1-UP; A6J1-UP; TAL1-UP; BJ61-UP; BS61-UP)

966K (S/N: PBG1-UP; TFS1-UP; NGX1-UP)

966M Series XE (S/N: P6C1-UP)

966M (S/N: DYC1-UP; KJP1-UP)

972H (S/N: GTA1-UP; LCC1-UP; A7D1-UP; NPE1-UP; A7G1-UP; A7J1-UP; WXZ1-UP)

972K (S/N: PEM1-UP; Z4W1-UP)

972M Series XE (S/N: EDW1-UP)

972M (S/N: A8P1-UP; JPR1-UP)

Introduction

Two rework procedures are available for the autolube lines depending on the configuration of the machine. Refer to ""Rework Procedure for the Autolube Lines Routing" " in order to verify the procedure that is adaptable to the machine.

Rework Procedure for the Autolube Lines Routing

The following machines are adaptable for the ""Procedure to Add Clip (With Machines Built Before November 2014)" ":

• 966H (S/N: A6D1-75001; A6G1-6072; A6J1-78002; BJ61-1350; BS61-414; RYF1-1870; TAL1-2775)

• 966K (S/N: PBG1-10001; TFS1-1381; NGX1-441)

• 966M Series XE (S/N: P6C1-397)

• 966M (S/N: DYC1-545; KJP1-895)

• 972H (S/N: A7D1-1138; A7G1-2332; A7J1-564; GTA1-786; LCC1-186; NPE1-226; WXZ1-257)

• 972K (S/N: PEM1-947; Z4W1-743)

• 972M Series XE (S/N: EDW1-267)

• 972M (S/N: A8P1-483; JPR1-400)

The following machines are adaptable for the ""Procedure to Remove Boss (With Machines Built After October 2014)" ":

• 966H (S/N: A6D75002-UP; A6G6073-UP; A6J78003-UP; BJ61-1351; BS66415-UP; RYF1871-UP; TAL2776-UP)

• 966K (S/N: PBG10002-UP; NGX442-UP; TFS1382-UP)

• 966M Series XE (S/N: P6C398-UP)

• 966M (S/N: DYC546-UP; KJP896-UP)

• 972H (S/N: A7D1139-UP; A7G2333-UP; A7J565-UP; GTA787-UP; LCC187-UP; NPE227-UP; WXZ258-UP)

• 972K (S/N: PEM948-UP; Z4W744-UP)

• 972M Series XE (S/N: EDW268-UP)

• 972M (S/N: A8P484-UP; JPR401-UP)

Procedure to Add Clip (With Machines Built Before November 2014)

Illustration 1	g03849207
View of tilt lever with new clip (A) 463-5391 Lever As (1) 4K-6177 Clip (2) 8T-4121 Hard Washer (3) 8T-4186 Bolt (4) 354-5137 Spacer

1. Install clip (1) on the autolube lines.

2. Insert spacer (4) between clip (1) and the tilt lever.

3. Secure clip (1) and spacer (4) to the tilt lever with bolt (3) and washer (2) .

Procedure to Remove Boss (With Machines Built After October 2014)

Illustration 2	g03849204
View of tilt lever with boss (B) 351-1906 Lever As (B) 351-1907 Lever As (C) Boss

Boss (C) will need to be removed in order to prevent interference with the autolube lines during movement of the tilt lever.