Electrical Connectors
Show/hide table
图 1 | g03838852 |
发动机 ECM 上接头的位置 (1) J1 ECM 接头 (2) J2 ECM 接头 |
电子控制模块(ECM)使用 86 端子的接头与配线线束相连。
电子控制模块 (ECM) 使用 64 端子的接头与配线线束相连。
Show/hide table
图 2 | g01746473 |
接头针脚 (从后端视图) 的布局 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 266-1683 | 拆卸工具 | 1 |
Show/hide table
图 3 | g01784793 |
拆下端子位置固定件 |
- 将接头从 ECM 上拆下。 请参阅拆解和组装, "电子控制模块 - 拆卸和安装"。
- 使用平口螺丝刀 (1) 拆下接头 (3) 端子定位部件 (2)。
注: 不要使用工具 (A) 拆下端子定位部件。
Show/hide table图 4 g01784822 拆卸工具 - 将工具 (A) 插入与端子相邻的孔内,从而松开锁定装置。
注: 确保工具与接头表面垂直。
- 将工具固定就位,并轻轻拉动导线,从而从接头 (3) 后部拆下端子。
- 从接头 (3) 正面拆下工具 (A)。
注: 如果必须更换端子,必须使用零件号 267-9572。
- 将端子插入接头 (3) 的后部,一直到端子与锁定装置扣合。
- 轻轻拉动导线,从而确保锁定装置将端子固定。
- 将两个端子定位部件 (2) 装入接头 (3) 侧部。
- 将接头与 ECM 相连。 请参阅拆解和组装, "电子控制模块 - 拆卸和安装"。
Show/hide table
图 5 | g03838886 |
Show/hide table
图 6 | g01240891 |
Show/hide table
图 7 | g01241538 |
Show/hide table
图 8 | g01355248 |
Show/hide table
图 9 | g01155187 |
Show/hide table
图 10 | g02219254 |
Show/hide table
图 11 | g02220494 |
Caterpillar Information System:
C4.4 and C7.1 Engines Component Location
3512C and 3516C Industrial Engines Air Inlet and Exhaust Lines
3524B and C175 Engines for Off-Highway Truck/Tractors Cylinder Block
G3606 and G3608 Engines Turbocharger - Install
Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7610} Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7610}
3516E Engines for 793D Off-Highway Trucks System Overview
3516E Engines for 793D Off-Highway Trucks Electronic Service Tools
C9.3 Marine Engine Housing (Front) - Remove and Install
C4.4 and C7.1 Engines General Information
C9.3 Marine Engine Fuel Filter Base - Remove and Install - Left-Hand Duplex
3512C and 3516C Industrial Engines Radiator
3512C and 3516C Industrial Engines Electronic Control Module
2015/05/28 Cat Reman Announces the Addition of Power Train Components for Mining Trucks {3030, 3258, 4008, 4051, 4201, 4251, 4267}
2015/06/26 New Software Is Used on 3512C Engines in 6060 Hydraulic Shovels {1920}
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Engine Air Filter Element - Clean/Replace
3516B Generator Set Engines with Dynamic Gas Blending Engine Stalls at Low RPM
3516B Generator Set Engines with Dynamic Gas Blending Engine Shutdown Occurs Intermittently
3512C and 3516C Industrial Engines Exhaust Manifold
3512C Generator Set Engine Air Starting Motor - Remove and Install
3516C High Displacement Engine Cooling Fan Control - Test
3516B Generator Set Engines with Dynamic Gas Blending Fuel Consumption Is Excessive
3516C High Displacement Engine Electrical Power Supply - Test
Installation Procedure for the Prelubrication Oil Pump on Certain G3500 Engines{1319} Installation Procedure for the Prelubrication Oil Pump on Certain G3500 Engines{1319}
3512C Generator Set Engine Electronic Control Module (Engine) - Remove and Install