G3606 and G3608 Engines Caterpillar


Turbocharger - Install

Usage:

G3606 JFE

安装步骤

表 1
所需工具 
工具  零件号  零件描述  数量 
Loctite C5A 防咬合剂 


    图 1g03838655

    注: 安装适配器时,注意 TOP(向上)。 放置时使传感器位于垂直位置。

  1. 将适当的起吊设备连接到涡轮增压器 (11) 上。 涡轮增压器 (11) 的重量大约为 305 kg (672 lb)

  2. 安装涡轮增压器 (11) 和螺栓 (10)。 拧紧螺栓 (10) 至扭矩为 460 ± 50 N·m (339 ± 37 lb ft)。 重新拧紧螺栓 (10) 至扭矩为 960 ± 100 N·m (708 ± 74 lb ft)


    图 2g03838478

  3. 安装螺栓 (8) 和螺栓 (9)。 将工具 (A) 涂抹到螺栓 (8) 和螺栓 (9) 上。 拧紧螺栓 (8) 至扭矩为 240 ± 40 N·m (177 ± 30 lb ft)


    图 3g03837929

  4. 安装防护罩 (4) 和螺栓 (6)。 将工具 (A) 涂抹到螺栓 (6) 上。 拧紧螺栓 (6) 至扭矩为 65 ± 5 N·m (48 ± 4 lb ft)

  5. 连接管组件 (5) 和管组件 (7)。


    图 4g03837566

  6. 连接温度传感器 (3)。 将温度传感器拧紧至扭矩为 45 ± 10 N·m (33 ± 7 lb ft)

  7. 安装弯头 (2) 和 V 形管箍 (1)。 将工具 (A) 涂抹到 V 形管箍 (1) 上。 拧紧 V 型带箍 (1) 至扭矩为 60 ± 5 N·m (44 ± 4 lb ft)

结束:

  1. 安装空气滤清器。

  2. 安装排气歧管护罩。

Caterpillar Information System:

Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7610} Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7610}
3516E Engines for 793D Off-Highway Trucks System Overview
3516E Engines for 793D Off-Highway Trucks Electronic Service Tools
C9.3 Marine Engine Housing (Front) - Remove and Install
C4.4 and C7.1 Engines General Information
C9.3 Marine Engine Fuel Filter Base - Remove and Install - Left-Hand Duplex
3512C and 3516C Industrial Engines Radiator
3512C and 3516C Industrial Engines Electronic Control Module
3512C and 3516C Industrial Engines Electronic Control Module
352F OEM Excavator Based Specialty Solutions Before Operation
PM3516 Power Modules Fire Prevention and Explosion Prevention
C3.3B and C3.8 Engines for Caterpillar Built Machines Diesel Particulate Filter Regeneration Does Not Occur
3524B and C175 Engines for Off-Highway Truck/Tractors Cylinder Block
3512C and 3516C Industrial Engines Air Inlet and Exhaust Lines
C4.4 and C7.1 Engines Component Location
C4.4 and C7.1 Engines Electrical Connectors
2015/05/28 Cat Reman Announces the Addition of Power Train Components for Mining Trucks {3030, 3258, 4008, 4051, 4201, 4251, 4267}
2015/06/26 New Software Is Used on 3512C Engines in 6060 Hydraulic Shovels {1920}
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Engine Air Filter Element - Clean/Replace
3516B Generator Set Engines with Dynamic Gas Blending Engine Stalls at Low RPM
3516B Generator Set Engines with Dynamic Gas Blending Engine Shutdown Occurs Intermittently
3512C and 3516C Industrial Engines Exhaust Manifold
3512C Generator Set Engine Air Starting Motor - Remove and Install
3516C High Displacement Engine Cooling Fan Control - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.