Housing (Front) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite High Flex Form In-Place Gasket | - |
Start By:
- Remove crankshaft front seal.
- Remove camshaft.
- Remove fuel filter base (if equipped).
- Remove bolts (1) and alternator (2).
Show/hide table
Illustration 2 g03834998 - Remove bolts (3) and alternator support bracket (4).
Show/hide table
Illustration 3 g03835016 - Remove bolts (5), front support (6), and the engine mounts (if equipped).
Show/hide table
Illustration 4 g03835032 - Remove bolts (7), bolts (8), bolts (10), and front housing (9).
Show/hide table
Illustration 1 | g03834961 |
- Install front housing (9) in the reverse order of removal.
- Apply Tooling (A) to the sealing surface of front housing (9) as shown in illustration 5.
Show/hide tableIllustration 5 g03835052
Caterpillar Information System:
C4.4 and C7.1 Engines General Information
C9.3 Marine Engine Fuel Filter Base - Remove and Install - Left-Hand Duplex
3512C and 3516C Industrial Engines Radiator
3512C and 3516C Industrial Engines Electronic Control Module
3512C and 3516C Industrial Engines Electronic Control Module
352F OEM Excavator Based Specialty Solutions Before Operation
PM3516 Power Modules Fire Prevention and Explosion Prevention
C3.3B and C3.8 Engines for Caterpillar Built Machines Diesel Particulate Filter Regeneration Does Not Occur
Visual Inspection of Liner Seats for 3400, C15, C16, and C18 Series Engines{1200} Visual Inspection of Liner Seats for 3400, C15, C16, and C18 Series Engines{1200}
C9.3 Marine Engine Air Starting Motor - Remove and Install
New Bellow Assemblies Are Used on Certain 3612 and C280-12 Marine and Petroleum Engines {1059, 1061} New Bellow Assemblies Are Used on Certain 3612 and C280-12 Marine and Petroleum Engines {1059, 1061}
3512C and 3516C Industrial Engines Jacket Water Heater Mount
3516E Engines for 793D Off-Highway Trucks Electronic Service Tools
3516E Engines for 793D Off-Highway Trucks System Overview
Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7610} Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7610}
G3606 and G3608 Engines Turbocharger - Install
3524B and C175 Engines for Off-Highway Truck/Tractors Cylinder Block
3512C and 3516C Industrial Engines Air Inlet and Exhaust Lines
C4.4 and C7.1 Engines Component Location
C4.4 and C7.1 Engines Electrical Connectors
2015/05/28 Cat Reman Announces the Addition of Power Train Components for Mining Trucks {3030, 3258, 4008, 4051, 4201, 4251, 4267}
2015/06/26 New Software Is Used on 3512C Engines in 6060 Hydraulic Shovels {1920}
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Engine Air Filter Element - Clean/Replace
3516B Generator Set Engines with Dynamic Gas Blending Engine Stalls at Low RPM