Exhaust System Contains Oil
- Turbocharger
- Valve guide seals
- Valve guides
- Piston rings
- Extended idle times
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Inspect for Failed Turbocharger Seals A. Check the following components for oil: - Inlet manifold - Exhaust manifold |
Turbocharger Seals |
Result: Oil from the turbocharger is not present in the inlet or exhaust manifold. Proceed to Test Step 2. Result: Oil from the turbocharger is present in the inlet or exhaust manifold. Repair:Replace the turbocharger. If the problem is not resolved, proceed to Test Step 2. |
2. Inspect the Valve Guide Seals A. Check the valve guide seals for the following: - Damage - Wear |
Valve Guide Seals |
Result: The valve guide seals are not damaged. Proceed to Test Step 3. Result: The valve guide seals are damaged. Repair:Replace the valve guide seals. If the problem is not resolved, proceed to Test Step 3. |
3. Inspect the Valve Guides A. Check the valve guides for wear. Refer to the Specification manual for the maximum permissible wear of the valve guides. |
Valve Guides |
Result: The valve guides are not worn. Proceed to Test Step 4. Result: The valve guides are worn. Repair: If necessary, recondition the cylinder head. Verify the repair. If the problem is not resolved, proceed to Test Step 4. |
4. Inspect the Piston Rings A. Piston rings that have excessive wear can cause too much pressure in the crankcase. The additional pressure in the crankcase will cause more than the normal amount of crankcase blowby from the crankcase breather. Use the following service tools, along with Software License, NETG5044: - 285-0901 Blowby Tool Gp (LARGE ENGINE) - 348-5430 Multi-Tool Gp |
Piston Rings |
Result: The piston rings are not worn. Proceed to Test Step 5. Result: The piston rings are worn. Repair: Replace the piston rings. If the problem is not resolved, proceed to Test Step 5. |
5. Check for Extended Idle Times Note: Extended idle times will allow oil to pass into the exhaust system. |
Idle Times |
Result: The idle times are extensive. Repair: Reduce the idle times. |
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Caterpillar Information System:
C9.3 Marine Engine Engine Oil Pan - Remove and Install - Combined Circuit Keel Cooling
C280-08 Tier 4 Engine Exhaust Manifold Shield - Remove and Install
C9.3 Marine Engine Engine Oil Pan - Remove and Install - Right-Hand Service
3500 Generator Sets with Dynamic Gas Blending Generator Bearing - Replace
2015/08/14 A New Control Valve Assembly for Fuel Is Used on Certain 3500 Marine Engines {1261}
3500 Generator Sets with Dynamic Gas Blending Generator Bearing - Inspect
2015/07/07 An Improved Housing for the Throttle Inlet Is Used on Certain G3500 Engines {1071}
12M Motor Grader Wheel Lean Bearings - Lubricate
3500B High Displacement Locomotive Engines Fuel Injector Mechanism
C9.3 Marine Engine Cylinder Head - Remove and Install
PM820, PM822, and PM825 Cold Planer Lifting and Tying Down the Machine - Fixed Conveyor
3600 Distillate Fuel Engines Maintenance Interval Schedule
C9.3 Marine Engine Engine Oil Pan - Remove and Install - Left-Hand Service Oil
Instructions for Installing AssetIQTM for Commercial Generator Set Systems on Caterpillar and non-Caterpillar Products {4450, 7490} Instructions for Installing AssetIQTM for Commercial Generator Set Systems on Caterpillar and non-Caterpillar Products {4450, 7490}
3500 Industrial Engines Fuel Injector Mechanism
3512C and 3516C Industrial Engines Engine Oil Filter
C280 Marine Engines Circuit Breaker - Test
3512C and 3516C Industrial Engines Air Lines
G3606 and G3608 Engines Aftercooler - Disassemble
C9.3 Marine Engine Coolant Temperature Sensor - Remove and Install
3516E Generator Set Engine Sensor Calibration Required - Test
C9.3 Marine Engine Engine Oil Pressure Sensor - Remove and Install
C280-08 Tier 4 Engine Exhaust Manifold - Remove and Install
C280-08 Tier 4 Engine Aftercooler - Remove and Install