Fuel Injector Mechanism
Show/hide table
Illustration 1 | g03836143 |
Show/hide table
Specification for 314-7626 Valve Mechanism Gp | |||
Item | Qty | Part | Specification Description |
1 | 1 | 317-1121 Jam Nut | Torque to |
2 | 1 | 6J-2245 O-Ring Seal | Lubricate the bore lightly with clean engine oil. |
3 | 1 | 7E-6508 Cap As | Start tightening the retainer nuts of the cap assembly by hand so that the terminal studs are not cross threaded.
Tighten the retainer nuts of the cap assembly to |
4 | 1 | 100-3878 Injector Spring | Length under test force is Test force is Free length after test is |
5 | 2 | 0L-2070 Bolt | Apply blue Loctite 243 to the threads of the bolt, if the bolts are removed after initial installation. |
B | 1 | 230-2620 Bushing | Bore of the bushing for the rocker arm shaft after assembly is Installation depth is |
C | 1 | 234-2273 Rocker Arm Shaft | Diameter is |
D | 1 | 282-7944 Injector Lifter As | Diameter is Bore in the cylinder head for the unit injector lifter assembly is |
Caterpillar Information System:
C9.3 Marine Engine Cylinder Head - Remove and Install
PM820, PM822, and PM825 Cold Planer Lifting and Tying Down the Machine - Fixed Conveyor
3600 Distillate Fuel Engines Maintenance Interval Schedule
C9.3 Marine Engine Valve Mechanism Cover - Remove and Install
C9.3 Marine Engine Cylinder Block Cover - Remove and Install
3500 Engines Housing (Front)
C2.2 Engines For Caterpillar Built Machines Sensor Signal (Analog, Passive) - Test
3406E Engine Cylinder Head - Install
The Hose and Tube Assembly in the Service Brake Control Group May Fail on Certain 777G Off-Highway Trucks{4257, 4269} The Hose and Tube Assembly in the Service Brake Control Group May Fail on Certain 777G Off-Highway Trucks{4257, 4269}
C27 and C32 Engine for MD6250 and MD6310 Drill Coolant Level - Test
XQC1200 and XQC1600 Power Modules Circuit Breaker Panel - Remove and Install
442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122} 442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}
12M Motor Grader Wheel Lean Bearings - Lubricate
2015/07/07 An Improved Housing for the Throttle Inlet Is Used on Certain G3500 Engines {1071}
3500 Generator Sets with Dynamic Gas Blending Generator Bearing - Inspect
2015/08/14 A New Control Valve Assembly for Fuel Is Used on Certain 3500 Marine Engines {1261}
3500 Generator Sets with Dynamic Gas Blending Generator Bearing - Replace
C9.3 Marine Engine Engine Oil Pan - Remove and Install - Right-Hand Service
C280-08 Tier 4 Engine Exhaust Manifold Shield - Remove and Install
C9.3 Marine Engine Engine Oil Pan - Remove and Install - Combined Circuit Keel Cooling
3516B Generator Set Engines with Dynamic Gas Blending Exhaust System Contains Oil
C9.3 Marine Engine Engine Oil Pan - Remove and Install - Left-Hand Service Oil
Instructions for Installing AssetIQTM for Commercial Generator Set Systems on Caterpillar and non-Caterpillar Products {4450, 7490} Instructions for Installing AssetIQTM for Commercial Generator Set Systems on Caterpillar and non-Caterpillar Products {4450, 7490}
3500 Industrial Engines Fuel Injector Mechanism