Housing (Front)
Show/hide table
图 1 | g03835244 |
Show/hide table
技术规格 - 4P-5427 前壳体总成 | |||
---|---|---|---|
项目 | 数量 | 零件 | 技术规格说明 |
1 | 4 | 9H-8260 螺栓 | 直径为 1/2 inch 的螺栓长度为 |
2 | 3 | 2A-5220 塞 | 拧紧至扭矩为 |
3 | 4 | 0S-1587 螺栓 | 直径为 1/2 inch 的螺栓长度为 |
4 | 1 | 3P-1896 杯塞 | 装配前,将 Loctite 540 涂覆到表面上。 |
5 | 10 | 1D-4593 螺栓 | 直径为 5/8 inch 的螺栓长度为 |
- | - | - | 装配后,将密封垫 (6) 和壳体面 (7) 调平。 |
- | - | - | 采用紧固件的标准扭矩。 |
Caterpillar Information System:
C2.2 Engines For Caterpillar Built Machines Sensor Signal (Analog, Passive) - Test
3406E Engine Cylinder Head - Install
The Hose and Tube Assembly in the Service Brake Control Group May Fail on Certain 777G Off-Highway Trucks{4257, 4269} The Hose and Tube Assembly in the Service Brake Control Group May Fail on Certain 777G Off-Highway Trucks{4257, 4269}
C27 and C32 Engine for MD6250 and MD6310 Drill Coolant Level - Test
XQC1200 and XQC1600 Power Modules Circuit Breaker Panel - Remove and Install
442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122} 442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}
C11, C13, C15, and C18 Industrial Engines NRS Exhaust Gas Temperature Is High
C9.3 Marine Engine Front Cover - Remove and Install
Procedure to Adjust Track Tension on Variable Gauge Undercarriages {4157, 4158} Procedure to Adjust Track Tension on Variable Gauge Undercarriages {4157, 4158}
3512C and 3516C Industrial Engines Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
Thinner Spacer Plates Not Recommended On Certain 3406E Through C18 On-Highway Truck Engines To Resolve Cylinder Liner Projection{1239} Thinner Spacer Plates Not Recommended On Certain 3406E Through C18 On-Highway Truck Engines To Resolve Cylinder Liner Projection{1239}
2015/05/15 A New Gas Tube Assembly Is Used on Certain 3512C Dynamic Gas Blending Oil Well Service Engines {1250}
C9.3 Marine Engine Cylinder Block Cover - Remove and Install
C9.3 Marine Engine Valve Mechanism Cover - Remove and Install
3600 Distillate Fuel Engines Maintenance Interval Schedule
PM820, PM822, and PM825 Cold Planer Lifting and Tying Down the Machine - Fixed Conveyor
C9.3 Marine Engine Cylinder Head - Remove and Install
3500B High Displacement Locomotive Engines Fuel Injector Mechanism
12M Motor Grader Wheel Lean Bearings - Lubricate
2015/07/07 An Improved Housing for the Throttle Inlet Is Used on Certain G3500 Engines {1071}
3500 Generator Sets with Dynamic Gas Blending Generator Bearing - Inspect
2015/08/14 A New Control Valve Assembly for Fuel Is Used on Certain 3500 Marine Engines {1261}
3500 Generator Sets with Dynamic Gas Blending Generator Bearing - Replace
C9.3 Marine Engine Engine Oil Pan - Remove and Install - Right-Hand Service