Check the Tilt Cylinder on Certain R1700G and R2900G Load Haul Dump Machines{5104}
- Load Haul Dump:
- R1700G (S/N: 8XZ1-408,410-465)
- R2900G (S/N: JLK1-547,700-1228)
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.
Problem
Tilt hydraulic cylinder may leak due to 167-2344 U-Cup Seal and 167-2225 Buffer Seal As failing.
Solution
Caterpillar is aware of the problem but an interim repair has not been defined.
Follow the instructions below if you have experienced this problem.
- Submit a Dealer Solution Network (DSN) ticket quoting CPI number 345913 and the Technical Information Bulletin media number
- Request that the Tier 1 representative, transfer your ticket to an available Tier 2 representative for Caterpillar Underground Mining Base Machine
- The Tier 2 representative will request the machine serial number
Show/hide table
Illustration 1 | g03831654 |
View of tilt cylinder (1) Buffer seal (2) U Cup seal |
Caterpillar Information System:
PL83 and PL87 Pipelayers Machine Systems Seat - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Counterweight Cylinder - Remove and Install
527 Track-Type Skidder Reference Material
New Steering Cylinders With Position Sensors are Now Available on Certain Motor Graders {4303, 7620} New Steering Cylinders With Position Sensors are Now Available on Certain Motor Graders {4303, 7620}
CB64B, CB66B and CB68B Asphalt Compactors Machine Systems Case Drain Flow for Piston Motor (Vibratory) - Test
CW34 Pneumatic Compactor Monitoring System
2015/05/14 Gear Inspection Should Be Performed When Replacing the Torsional Coupler on Certain 14M and 16M Motor Graders {3063}
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Determining Diagnostic Trouble Codes
CW34 Pneumatic Compactor Air Compressor Oil - Change
A SOS Port Can be Installed for Engine Oil Sampling on F2 Series Backhoe Loaders and Industrial Loaders Equipped with a C3.4 Engine {1306, 1308, 7542} A SOS Port Can be Installed for Engine Oil Sampling on F2 Series Backhoe Loaders and Industrial Loaders Equipped with a C3.4 Engine {1306, 1308, 7542}
CW34 Pneumatic Compactor Lifting and Tying Down the Machine
CW16 Pneumatic Compactor Ballast Information
Check the Tilt Cylinder Line Relief Valve on R3000H Load Haul Dump Machines{5117} Check the Tilt Cylinder Line Relief Valve on R3000H Load Haul Dump Machines{5117}
Check Lift Arm Welds on R3000H Load Haul Dump Machines{6107} Check Lift Arm Welds on R3000H Load Haul Dump Machines{6107}
PL83 and PL87 Pipelayers Machine Systems Counterweight Sections - Remove and Install
Procedure to Install Machine Automation System on R1600H Load Haul Dump Machines {7000, 7600} Procedure to Install Machine Automation System on R1600H Load Haul Dump Machines {7000, 7600}
PL83 and PL87 Pipelayers Machine Systems Fairlead Sheave - Remove and Install
C2.2 Engines For Caterpillar Built Machines Glow Plug Starting Aid - Test
24M Motor Grader Rim - Inspect
C2.2 Engines For Caterpillar Built Machines Injector Solenoid - Test
415F2 and 427F2 Backhoe Loaders Engine Supplement Radiator, Fuel Cooler, After Cooler, and Hydraulic and XMSN Oil Cooler - Remove and Install
793F Off-Highway Truck (Command For Hauling) Machine Systems Front Wheel Bearings - Remove
777G Off-Highway Truck Steering System Steering Shaft (Cover Plate) - Check and Adjust
793F Off-Highway Truck (Command For Hauling) Machine Systems Front Wheel Bearings - Install