Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite 771 Anti-Seize Compound | - |
- Remove panel (1).
Show/hide table
Illustration 2 g03783245 Note: Mark the orientation of harness assembly (3) for assembly purposes.
- Disconnect harness assembly (3). Cut any cable straps for harness assembly (3).
- Remove temperature sensor (flame detect) (2).
Show/hide table
Illustration 3 g03783258 - Open door (4).
Show/hide table
Illustration 4 g03783280 - Remove temperature sensor (DPF inlet) (5).
Show/hide table
Illustration 1 | g03783225 |
- Install the temperature sensor (DPF inlet) (5), and temperature sensor (flame detect) (2) in the reverse order of removal.
Note: Always replace the metal cable straps with a comparable cable strap. Do not use plastic cable straps.
Note: Route harness assembly (3) in the original location to protect harness assembly from heat.
- Apply Tooling (A) to the threads on temperature sensor (flame detect) (2) and to the threads of temperature sensor (DPF inlet) (5). Tighten temperature sensor (flame detect) (2) and temperature sensor (DPF inlet) (5) to a torque of
45 ± 5 N·m (33 ± 4 lb ft) .
- Apply Tooling (A) to the threads on temperature sensor (flame detect) (2) and to the threads of temperature sensor (DPF inlet) (5). Tighten temperature sensor (flame detect) (2) and temperature sensor (DPF inlet) (5) to a torque of
Caterpillar Information System:
C280 Marine Engines Fuel Pressure Is High
C13 Generator Set Engine Pressure Sensor (ARD Combustion Air) - Remove and Install
C4.4 and C6.6 Engines Crankcase Breather Ejects Oil
Procedure for Installing Three Phase Flywheel Inverter On Certain Uninterruptible Power Supply{4480} Procedure for Installing Three Phase Flywheel Inverter On Certain Uninterruptible Power Supply{4480}
C13 Generator Set Engine Fuel Temperature Sensor - Remove and Install
C13 Generator Set Engine Fuel Pressure Sensor - Remove and Install
C13 Generator Set Engine Crankcase Pressure Sensor - Remove and Install
C13 Generator Set Engine Engine Oil Pressure Sensor - Remove and Install
3512E Engines Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
2015/01/23 New Varistor is Now Available for Certain Engines and Generator Sets {4450}
3512E Engines Engine Oil Temperature Sensor - Remove and Install
3512E Engines Inlet Air Temperature Sensor - Remove and Install
3516B Generator Set Engines with Dynamic Gas Blending Fuel Pressure Is Low
Final Drive Motor Housings Are Available for Certain Excavators {4050} Final Drive Motor Housings Are Available for Certain Excavators {4050}
C13 Generator Set Engine Temperature Sensor (Catalyst Inlet) - Remove and Install
Turbine Blades May Shift In Certain C280 And 3600 Engine ABB Turbochargers{1052} Turbine Blades May Shift In Certain C280 And 3600 Engine ABB Turbochargers{1052}
C13 Generator Set Engine Pressure Sensor (DPF) - Remove and Install
C13 Generator Set Engine Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C2.2 Engines for Caterpillar Built Machines Crankshaft
C13 Generator Set Engine Pressure Sensor (Cooled Exhaust Gas) - Remove and Install
C13 Generator Set Engine Pressure Sensor (NRS Differential) - Remove and Install
C13 Generator Set Engine Pressure Sensor (NRS Absolute) - Remove and Install
2015/05/15 A New Starter Is Now Available for Certain Cat® Generator Set Engines {1453}
C13 Generator Set Engine Boost Pressure Sensor - Remove and Install