C32 Marine Engine Caterpillar


Maintenance Interval Schedule - Engines Which Are Rated "B" and Engines Which Are Rated "C"

Usage:

C32 RXB
在进行任何操作或维护步骤之前,确保已阅读并理解所有的安全信息、警告和说明。

用户对所有保养行为负责,包括以下内容:执行所有调整, 使用正确的润滑剂、油液和滤清器 和 用新部件更换正常磨损和老化的旧部件。

未能遵照正确的保养周期和步骤可能导致产品性能降低和/或部件磨损加速。

在进行每个后续周期的保养之前,必须先进行前一个周期的所有保养。

选择先到的间隔以确定正确的保养周期: 燃油消耗量, 工时 和 日历时间。 在恶劣作业条件下工作的产品可能需要更频密的保养。

所有以下情况会影响换油周期:工作条件, 燃油类型, 机油类型 和 集油槽尺寸。 定期机油取样可以分析旧机油,以便确定换油周期是否适合于您的特定发动机。

请参考本操作和保养手册, "发动机机油和滤清器 - 更换" 以确定适合于您的特定发动机的换油周期。

为了确定大修保养周期,请参考本操作和保养手册, "保养建议 "。

需要时即进行的保养

蓄电池 - 更换
蓄电池或蓄电池电缆 - 断开
发动机 - 清洁
发动机机油油位尺 - 校准
发动机贮存程序 - 检查
燃油系统 - 充油
热交换器 - 检查
保养建议
海水滤网 - 清洁/检查
锌棒 - 检查/更换

每天的保养

冷却系统冷却液液位 - 检查
发动机空气滤清器保养指示器 - 检查
发动机机油油位 - 检查
燃油系统粗滤器/油水分离器 - 放水
围绕检查

初次10工作小时

皮带 - 检查/调整/更换

每50个工作小时或 每周 一次的保养

海水滤网 - 清洁/检查
锌棒 - 检查/更换

最初500小时(新系统、重新加注的系统和更换冷却液种类的系统)的保养

冷却系统冷却液液样(2级) - 采样

每年的保养

冷却系统冷却液液样(2级) - 采样

每6000个工作小时或3年

冷却系统长效冷却液(ELC)延长剂 - 添加

每6年

后冷器芯 - 更换

每12000个工作小时数或每6年的保养

冷却系统冷却液[长效冷却液(ELC)] - 更换

初次消耗完22 700升(6000美加仑)燃油后或工作250小时后

发动机气门间隙 - 检查/调整

每消耗22 700升(6000美加仑)燃油或每250个工作小时数或1年

辅助水泵(橡胶叶轮) - 检查
蓄电池电解液液位 - 检查
皮带 - 检查/调整/更换
冷却系统冷却液液样(1级) - 采样
冷却系统冷却液补充添加剂(SCA) - 测试/添加
发动机 - 清洁
发动机空气滤清器滤芯 - 清洁/更换
发动机曲轴箱呼吸器 - 清洗
发动机机油油样 - 采样
发动机机油和滤清器 - 更换
燃油系统粗滤器(油水分离器)滤芯 - 更换
燃油系统细滤清器 - 更换
燃油箱中的水和沉渣 - 排放
软管和卡箍 - 检查/更换

每消耗90 850升(24 000美加仑)燃油或每1000个工作小时数

后冷器芯 - 清洁/测试
封闭式曲轴箱通风(CCV)烟雾处理滤清器 - 更换
涡轮增压器 - 检查

每消耗272 550升(72 000美加仑)燃油或每3000个工作小时数

辅助水泵(青铜叶轮) - 检查
冷却系统冷却液[柴油发动机防冻剂/冷却液(DEAC)] - 更换
冷却系统水温调节器 - 更换
曲轴减振器 - 检查
发动机安装支座 - 检查
发动机速度/正时传感器 - 检查/清洁/标定
发动机气门间隙 - 检查/调整
发动机气门转子 - 检查
热交换器 - 检查
起动马达 - 检查

每消耗454 250升(120 000美加仑)燃油或每5000个工作小时数

交流发电机 - 检查
水泵 - 检查

大修

保养建议
大修(整体)

Caterpillar Information System:

C32 Marine Engine Maintenance Interval Schedule - Engines Which Are Rated "E"
G3600 A4 Engines Pressure Regulating Valve
G3600 A4 Engines Engine Governing - Adjust
G3600 A4 Engines General Information (Electronic Control System)
Generators for C15/C18 Engines Mechanical Features
C3.3 Industrial Engine Engine Operation
C4.4 and C6.6 Engines Valve Lash Is Excessive
G3600 A4 Engines Ignition System
3512E Engines Air Cleaner - Remove and Install
G3600 A4 Engines BTU and Precombustion Chamber Adjustments
G3600 A4 Engines Excessive Engine Oil Consumption - Inspect
G3600 A4 Engines Measuring Engine Oil Pressure
3600 Heavy Fuel Engines Maintenance Interval Schedule - Heavy Fuel
C3.3 Industrial Engine Reference Material
3512E Engines Inlet Air Temperature Sensor - Remove and Install
3512E Engines Engine Oil Temperature Sensor - Remove and Install
2015/01/23 New Varistor is Now Available for Certain Engines and Generator Sets {4450}
3512E Engines Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C13 Generator Set Engine Engine Oil Pressure Sensor - Remove and Install
C13 Generator Set Engine Crankcase Pressure Sensor - Remove and Install
C13 Generator Set Engine Fuel Pressure Sensor - Remove and Install
C13 Generator Set Engine Fuel Temperature Sensor - Remove and Install
Procedure for Installing Three Phase Flywheel Inverter On Certain Uninterruptible Power Supply{4480} Procedure for Installing Three Phase Flywheel Inverter On Certain Uninterruptible Power Supply{4480}
C4.4 and C6.6 Engines Crankcase Breather Ejects Oil
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.