2014/09/16 Caterpillar


New Inspection and Repair Procedure Is Now Available for Cat® Products Located in India Equipped with Product Link {7606}

Usage:

D3400 01T
Caterpillar Products:
  • All
  • Service Magazine SEPD1852, 16 September 2014, "New Inspection and Repair Procedure Is Now Available for Cat® Products Located in India Equipped with Product Link". Disregard the information in the article that is listed above. Refer to the information in the following article.

    A new Inspection and repair procedure is now available for Cat® Products located in India equipped with Product Link. The new procedure addresses the configuration of machines with Product Link that are not reporting machine information on Cat® Products located in North, North Central, North West, and North Eastern regions of India.

    New Inspection and Repair Procedure

    Perform the following procedure to configure machines that are equipped with Product Link:

    PL522 Harness Connectivity

    1. Verify the PL522 harness connection with the machine harness.



      Illustration 1g03705821

      Routing of wiring harness between PL522 ECM and antenna

    1. Check the antenna wiring connection between the PL522 ECM and antenna.

    1. Verify that the antenna location should be placed on machine as per PL522 installation procedure. Refer to Special Instruction, REHS2368, "Installation Procedure for Product Link PL522/523 (Cellular)" for PL522 installation procedure.

    1. Perform the PL522 installation procedure to verify the wiring connection between machine harness and antenna.

    Hardware Connectivity

    SIM Card Detection

    The following GSM Information is to be checked using Caterpillar Electronic Technician (Cat ET) to identify if the SIM card is connected.

    • SIM Card Status

    • SIM Card Number

    • IMEI Number




    Illustration 2g03708062

    If the Cat ET shows similar to Illustration 2, perform the following procedure to resolve the hardware issue "SIM card not detected":

    1. Register the new PL522 ECM in VisionLink.

    1. Replace the faulty PL522 ECM with a new PL522 ECM.

    1. Verify the data in VisionLink after installing the new PL522 ECM.

    SIM Card Readiness

    The following GSM Information is to be checked using Cat ET to identify the readiness of the SIM Card.

    • SIM Card Status

    • SIM Card Number

    • IMEI Number




    Illustration 3g03705823

    If the Cat ET shows similar to Illustration 3, perform the following procedure to resolve the hardware issue "SIM card not ready":

    1. Register the new PL522 ECM in VisionLink.

    1. Replace the faulty PL522 ECM with a new PL522 ECM.

    1. Verify the data in VisionLink after installing the new PL522 ECM.

      Note: Before downloading the data from Product Link, wait for 5 minutes after the machine key ON.

    APN Configuration




      Illustration 4g03728038

    1. Cellular Packet Data Protocol (PDP) context Activation status should be "Missing or Unknown APN".

    1. Cellular Network Coverage status should be "In Coverage".

    1. Cellular Device Data Network Registration Status should be "Attached Roaming".



      Illustration 5g03724782

    1. Verify the GSM parameters and APN configuration mentioned in Illustration 5 to confirm the APN Configuration Status.

    1. Raise a Salesforce ticket with all the machine information (PSR, GSM, APN report).

    Caterpillar Information System:

    3512E Land Electric Drive Maintenance Interval Schedule
    2015/07/17 A New Bracket Is Used to Mount the Boost Pressure Sensor on Certain Marine 3500C Engines {1408, 1439}
    C3.4B Engines Glow Plug Starting Aid - Test
    C4.4 Engines for Caterpillar Built Machines Fuel Injection
    XQ125 Generator Set Clean Emissions Module Support - Inspect
    XQ2000 Power Module Fuel Tank Strainer - Clean
    XQC1200 Power Module Fan Motor - Lubricate
    C0.5 and C0.7 Industrial Engines Severe Service Application
    3516E Generator Set Engine Aftercooler - Two Stage Aftercooler
    2015/02/10 New Bearings with a Reduced Inside Diameter are Available for the Elimination of Radial Play in the Front Linkage for Certain D Series and E Series Excavators, Forest Machines, and Mobile Hydraulic Power Units {6513}
    C7.1 Marine Engine Exhaust Manifold
    C7.1 Marine Engine Fuel Manifold (Rail)
    2014/09/11 Cat® Reman Announces the Addition of Transmission Clutch Plates for Certain Machine Transmissions {3160}
    2014/09/12 Cat® Reman Announces the Addition of Transmission Clutch Plates for Certain Petroleum Engines {3160}
    C7.1 Marine Engine Exhaust Temperature Sensor
    2014/09/12 Cat® Reman Now Offers New Turbocharger and Cartridge Groups for Certain Commercial Engines {1052, 1053}
    C18 Fire Pump Engine Product Description
    C3.4B Engines Injector Data Incorrect - Test
    2014/09/12 Cat® Reman Now Offers New Turbocharger and Cartridge Groups for Certain Truck Engines {1052, 1053}
    2014/09/26 The Adjustment Screw Used For Certain C175 Rocker Arm Assemblies Has Been Improved {1123}
    C18 Fire Pump Engine Sensors and Electrical Components
    C18 Fire Pump Engine Starting the Engine
    C18 Fire Pump Engine Engine Operation
    C18 Fire Pump Engine Engine Stopping
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.