Coolant Temperature Is Low
按照此步骤以对冷却液温度低进行故障诊断与排除。
- 极端的环境温度
- 冷却系统故障
- 冷却液温度传感器
- 水温调节器
注: 下面以概率的先后顺序列出了这些步骤。 依次完成这些步骤。
Show/hide table
热的冷却液、蒸汽和碱会造成人身伤害。 在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。 只有当发动机停机且散热器盖已经冷却到可以徒手触摸时,再慢慢拆下过滤器盖以释放压力。 冷却系统调节器含碱。 应避免它与皮肤和眼睛接触。 |
Show/hide table
故障诊断与排除测试步骤 | 数值 | 结果 |
1. 确保发动机配备符合环境条件 A. 确保发动机配备符合环境条件。 |
发动机操作 |
结果:发动机配备符合环境条件要求。 转至测试步骤 2。 结果:发动机配备不符合环境条件要求。 修理:有关寒冷天气操作所需设备的更多信息,请参阅操作和保养手册。 |
2. 检查冷却系统 A. 检查冷却液液位。 B. 检查冷却液有无泄漏迹象。 注释:如果冷却液温度传感器没有浸泡在冷却液中,可能出现错误读数。 |
发动机冷却液液位 |
结果:发动机冷却液液位正常。 转至测试步骤 3。 结果:发动机冷却液液位不正常。 修理:检查冷却系统有无泄漏。 关于更多信息,参考故障排除, "冷却液液位低"。 修理所有泄漏的地方。 |
3. 冷却液温度传感器故障 A. 检查电子维修工具上的冷却液温度读数。 当发动机热时,温度应稳定升高。 确保温度如预期所料。 |
冷却液温度传感器故障 |
结果:冷却液温度如预期所料。 修理:检测到故障的冷却液温度传感器。 更换温度传感器。 结果:冷却液温度如预期所料。 继续测试步骤 4。 |
4. 检查发动机冷却液系统 A. 把钥匙开关转到断开位置。 B. 连接电子维修工具。 C. 起动发动机。 D. 监控状态屏幕中的"发动机冷却液温度" |
冷却液温度 |
结果:冷却液温度达到操作温度。 使机组返回工作。 结果:冷却液温度未达到操作温度。 修理:测试水温调节器。 请参阅系统操作、测试和调整, "水温调节器 - 测试"。 如果测试失败,更换水温调节器。 请参阅拆解和组装, "水温调节器 - 拆卸和安装"。 如果仍存在故障,联系代理商解决方案网络(DSN)。 |
Caterpillar Information System:
C4.4 Engines Clean Emissions Module Has High Oxygen Level
C3.4B Engines DEF Return Valve - Test
C4.4 Engines Acceleration Is Poor or Throttle Response Is Poor
C175-16 PETROLEUM ENGINES Temperature Sensor (Coolant, Block Outlet) - Remove and Install
C175-16 PETROLEUM ENGINES Pressure Sensor (Coolant, Block Inlet) - Remove and Install
2014/09/05 A New Method Is Available to Update Some Color Marine Power Displays with the Correct Device ID on Certain Engines {1900, 7400, 7402, 7450, 7451, 7490}
XQC1200 Power Module Safety Messages
2014/10/31 A New Improved Oil Filter Housing Cover Is Used on Certain C175-16 Engines {1306}
3512E HD Petroleum Engine Starting Motor - Inspect
3512E HD Petroleum Engine Overhaul (Major)
Updating the 350-3013 Engine Harness As Connector Used on 3512C Petroleum Well Fracturing Engines{1408, 7553} Updating the 350-3013 Engine Harness As Connector Used on 3512C Petroleum Well Fracturing Engines{1408, 7553}
C175-16 PETROLEUM ENGINES Pressure Sensor (Air Inlet Manifold) - Remove and Install
2014/09/05 New Software Is Used on Certain C13 Industrial Engines in Atlas Copco Compressors {1901, 1920}
EMCP 4.3/4.4 Panel Installation for 3512C and 3512C HD Land Drilling Applications{4490} EMCP 4.3/4.4 Panel Installation for 3512C and 3512C HD Land Drilling Applications{4490}
C3.3 Industrial Engine Fuel System Primary Filter (Water Separator) Element - Replace
C4.4 Engines DEF Pressure Is High
C175-16 PETROLEUM ENGINES Pressure Sensor (Coolant, Block Outlet) - Remove and Install
320D2 Excavator Stopping the Engine
Cat Commercial Diesel Engine Fluids Recommendations Distillate Diesel Fuel
C175-16 PETROLEUM ENGINES Engine Speed Sensor - Remove and Install
Procedure to Inspect and Repair the Front Wheels on 785 - 797 Off-Highway Truck {0599, 0700, 0730, 0731, 4006, 4200, 4209, 4251} Procedure to Inspect and Repair the Front Wheels on 785 - 797 Off-Highway Truck {0599, 0700, 0730, 0731, 4006, 4200, 4209, 4251}
C175-16 PETROLEUM ENGINES Oil Mist Detector - Remove and Install
C3.3 Industrial Engine Fuel System Primary Filter/Water Separator - Drain
C3.3 Industrial Engine Fuel System Secondary Filter - Replace