Improper Installation of the 274-6717 Crankcase Pressure Sensor on 3500 Commercial Engines{1408, 1439, 1916}
- Engine: All 3500 Engines
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.
Problem
Several 274-6717 Crankcase Pressure Sensors have been oriented incorrectly on the assembly line. This incorrect orientation can cause residual oil accumulation in the sensor and intermittent crankcase pressure faults.
Solution
If intermittent crankcase pressure faults are being experienced, reorient the pressure sensor to a near vertical position. Refer to Illustrations 1 and 2 for the examples of the incorrect and correct orientation.
Show/hide table
Illustration 1 | g03707644 |
Incorrect orientation |
Show/hide table
Illustration 2 | g03707655 |
Correct orientation |
Caterpillar Information System:
2014/08/01 A New Alternator and Mounting Hardware Are Used For Certain G3306B Engines {1405}
XQC1200 and XQC1600 Power Modules Engine Oil Pressure Sensor - Remove and Install - Filtered and Unfiltered
PM820, PM822, and PM825 Cold Planer Track Drive Planetary Oil Level - Check
PM820, PM822, and PM825 Cold Planer Track Drive - Inspect
PM820, PM822, and PM825 Cold Planer Steering Cylinder Ends - Lubricate
XQC1200 and XQC1600 Power Modules Turbocharger Inlet Temperature Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Rotor Service Door Pivot Pins - Lubricate
PM820, PM822, and PM825 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
XQC1200 and XQC1600 Power Modules Turbocharger Inlet Pressure Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil Level - Check
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil - Change
2014/08/08 New Engine Software Is Used on Certain 3512C Well Fracturing Engines {1901, 1920}
2014/08/15 New Turbocharger Support Bolts Are Used on 3512C HD Drilling Engines {1052, 7553}
2014/08/15 New Oil Cooler and Turbochargers Are Available for Certain 3512C Land Drilling Engines {1052, 1053, 1378}
2014/10/03 New Aftercooler Elbow Mounting Brackets Are Now Used On Certain 3600 and C280 Engines {1063, 1063}
460-9231 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9231 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
G3516 TA Engine Fuel Pressure Is High
460-9243 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9243 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
G3516 TA Engine Fuel Pressure Is Low
460-9353 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9353 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
C3.4B Engines Oil Contains Fuel
460-9788 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9788 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
3516C and C175-16 Engines Selective Catalytic Reduction NOx Conversion Is Low