Diesel Exhaust Fluid Quality - Test
注: 请参考操作和保养手册, 油液建议 - 柴油机排气处理液了解 DEF 处理和存放步骤
Show/hide table
所需工具 | ||
数量 | 零件号 | 零件描述 |
1 | ||
1 | 431-7087 | 工具总成 (折射计(DEF)) |
1 | 162-5791 | 抹布 |
2 | 169-8373 | 油液取样瓶 |
1 | 1U-5718 | 真空泵 |
1 | 4C-4600 | 容器 |
1 | 1U-7648 | 切管机 |
1 | 466-8796 | 测试条 |
所需长度 | 1U-8757 | 管 |
1 | 457-6144 | 工具组件 - 钳子 |
- 拆卸任何部件前,清除 DEF 罐上的所有碎屑。 DEF 污染可影响测试结果。
Show/hide table
图 1 g03706721 (1) DEF 罐加注口盖
(2) DEF 罐滤网 - 将加注口盖 (1) 从柴油机排气处理液 (DEF) 罐上拆下。
- 使用工具组件 - 钳子压下以释放凸舌。 将滤网 (2) 从 DEF 罐的加注口颈上拆下。
Show/hide table
图 2 g03706724 (3) 真空泵螺母
(4) 1U-5718 真空泵
(5) 1U-8757 管注: 为确保 DEF 样品在提取过程中不受污染,每次执行此步骤时,请使用一段新的管 (5)。
- 将管 (5) 从塑料袋中取出,并安装到真空泵 (4) 中。
- 松开螺母 (3),以便安装管。
- 将管一直安装到真空泵的盖上,如图 2 所示。
- 将真空泵顶部的螺母拧到底,以防止 DEF 泄漏。
- 从塑料袋中取出液体取样瓶。 取下盖,并将液体取样瓶安装到真空泵上。
Show/hide table
图 3 g03706727 (5) 1U-8757 管
(6) DEF 罐加注口颈注: 必须只能从 DEF 罐所含油液的顶层部分采集 DEF 液样。 污染物位于 DEF 的顶层部分。
- 将管 (5) 的另一端置于 DEF 罐 (6) 的加注口颈中。
- 使用真空泵从罐的顶层油液中提取 DEF。 将液体取样瓶加注到瓶上的"加注管"处。
- 转至 "DEF 污染测试步骤",开始污染测试。
- 将测试条置于液体取样瓶中 5 秒。
Show/hide table
图 4 g03707382 (7) 阴性测试结果
(8) 阳性测试结果 - 取下测试条,查看有无图 4 所示的变色。 测试条的任何变色表明 DEF 被油基液体污染。 请联系代理商解决方案网络,了解进一步的信息。
注: 如果测试条显示 DEF 没有污染,转至 "DEF 浓度测试步骤"。
- 按照折射计随附的说明校准仪表的吃水线。
- 清洁折射计,然后涂抹两滴从 DEF 罐中收集的柴油机排气处理液(DEF)。
Show/hide table
图 7 g03370573 良好状态下 DEF 的典型读数 - 读取折射计中的 DEF 质量。 DEF 质量的测量值必须在 29% 和 35% 之间。 如果 DEF 不符合技术规格,则用新的 DEF 更换储罐内的 DEF。 新的 DEF 必须符合 ISO 22241 标准。
注: 按照当地法规处置清除的 DEF。
Show/hide table
图 5 | g03370564 |
431-7087 工具总成 (折射计(DEF)) |
Show/hide table
图 6 | g03370553 |
蒸馏水的标定点 |
Caterpillar Information System:
C8.7 Marine Engine Decommissioning and Disposal
PM620 and PM622 Cold Planer Coolant Sample (Level 1) - Obtain
PM620 and PM622 Cold Planer Cooling System Coolant Level - Check
PM620 and PM622 Cold Planer Cooling System Coolant (ELC) - Change
C8.7 Marine Engine Fumes Disposal Filter Element - Replace
PM620 and PM622 Cold Planer Conveyors - Lubricate
C8.7 Marine Engine Fuel System Secondary Filter - Replace
PM820, PM822, and PM825 Cold Planer Belt - Inspect/Adjust/Replace
C0.5 and C0.7 Industrial Engines Mounting and Dismounting
C8.7 Marine Engine Engine Oil and Filter - Change
PM620 and PM622 Cold Planer Battery or Battery Cable - Inspect/Replace
PM620 and PM622 Cold Planer Battery - Clean/Check
PM620 and PM622 Cold Planer Engine Oil Level - Check
460-8974 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-8974 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
C9.3 Industrial Engine and CX31-P600-C9I Petroleum Power Train Package Maintenance Interval Schedule
PM820, PM822, and PM825 Cold Planer Fuel Tank Water and Sediment - Drain
PM820, PM822, and PM825 Cold Planer Hydraulic Foldable Canopy Cylinder Ends - Lubricate
PM620 and PM622 Cold Planer Hydraulic System Oil Level - Check
PM620 and PM622 Cold Planer Hydraulic System Oil Sample - Obtain
460-9068 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9068 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
PM820, PM822, and PM825 Cold Planer Legs (Struts) - Lubricate
PM820, PM822, and PM825 Cold Planer Moldboard Cutting Edge - Inspect/Adjust/Replace
XQC1200 and XQC1600 Power Modules Inlet Manifold Pressure Sensor - Remove and Install
XQC1200 and XQC1600 Power Modules Inlet Manifold Temperature Sensor - Remove and Install