Final Drive Spindle and Service Brake - Disassemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0520 | Driver Gp | 1 |
Start By:
- Remove the final drive, the wheel, and the service brake piston housing .
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be cleaned thoroughly. Cleaning will help to prevent dirt from entering the internal mechanism.
- Position spindle assembly (1) in a vertical position with the brake assembly facing upward.
- Remove O-ring seal (2).
- Remove retaining ring (3).
- Remove hub (4) from spindle assembly (1).
Show/hide table
Illustration 2 g03692519 - Remove outer plate (5), friction disc (6), outer plate (7), friction disc (8), outer plate (9), friction disc (10), outer plate (11), friction disc (12), and outer plate (13) from spindle assembly (1).
Note: Steps 6 through 12 are for the disassembly of the service brake piston housing.
Show/hide tableIllustration 3 g03692526 Show/hide tableIllustration 4 g03692531 Show/hide tablePersonal injury can result from being struck by parts propelled by a released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to release the spring force.
- Use Tooling (A) and a suitable press in order to compress springs (17) on piston housing (14).
- Remove retaining pins (15) (not shown) from spring guides (16).
- Release the pressure from the suitable press. Remove springs (17) and spring guides (16) from piston housing (14).
Show/hide table
Illustration 5 g03692532 - Remove retaining ring (18), hard washer (19), and pin (20) from piston housing (14).
Show/hide table
Illustration 6 g03692534 - Remove hollow dowel (21) and O-ring seal (22) from piston housing (14).
Show/hide table
Illustration 7 g03692536 Typical Example - To separate piston (23) from piston housing (14), block purge port (25) and apply a small amount of pressure to pressure port (24). Remove piston (23) from piston housing (14).
Show/hide table
Illustration 8 g03692539 - Remove outer seal (26) and inner seal (27) from piston housing (14).
Show/hide table
Illustration 1 | g03692277 |
Caterpillar Information System:
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Pressure Tap Locations
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Hydraulic Fan Speed - Test and Adjust
The Third Clutch Friction Disc May Fail on Certain 777 Off-Highway Trucks{3054, 3155, 3160} The Third Clutch Friction Disc May Fail on Certain 777 Off-Highway Trucks{3054, 3155, 3160}
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Piston Pump Margin Pressure (Hydraulic Fan) - Test and Adjust
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Piston Pump Cutoff Pressure (Hydraulic Fan) - Test and Adjust
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Main Pump (Destroke Pressure) - Test and Adjust
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Main Pump - Test - Test without Flow Meter
AP1000F Asphalt Paver Machine Systems Auger Conveyor - Mounting
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Case Drain (Main Pump) - Test
AP1000F Asphalt Paver Machine Systems Communication Electronic Control Module (Product Link)
M314F, M316F, M318F, M320F and M322F Wheeled Excavators Machine Only Operates in Travel Mode
M314F, M316F, M318F, M320F and M322F Wheeled Excavators Machine Only Operates in Power Mode
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Main Pump (Maximum Displacement) - Test and Adjust - Test without Flow Meter
PM-200 Cold Planer Maintenance Interval Schedule
2014/08/01 New VIMSTM Software is Now Available On Certain Off-Highway Truck/Tractors {7601, 7620}
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Relief Valve (Signal Limiter) - Test and Adjust
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Relief Valve (Main) - Test and Adjust
794 AC Off-Highway Truck Machine Systems Pump Drive
Rework Procedure to Update AP1000B and AP1055B Asphalt Pavers with 25KW Generator Group {5639} Rework Procedure to Update AP1000B and AP1055B Asphalt Pavers with 25KW Generator Group {5639}
AP655F and AP655F L Asphalt Paver Machine Systems Power Crown Group
AP1000F Asphalt Paver Propel System Bogie
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor
C3.4B Industrial Engine Welding on Engines with Electronic Controls
C3.4B Industrial Engine Coolant (DEAC) - Change