A New Jacket Water Elbow and Tube Assembly Are Used on Certain 3516C HD Marine Tier 3 Engines {1380}
- Engine:
- 3516C (S/N: TKG1-UP; TKT1-UP; TKX1-UP; TKY1-UP)
Description of Change: The new jacket water elbow and tube assembly are more robust to relative motion.
Adaptable To: The new 446-0380 Elbow and 446-0378 Tube As replace the existing 390-7470 Elbow and 375-7973 Tube. The new elbow and tube assembly are adaptable back to first production on the serial numbers listed above.
Refer to Table 1 for a list of part numbers needed to install the new elbow and tube assembly.
Show/hide table
New Part Number     | Description     | Quantity     |
0S-1571     | Bolt     | 2     |
5M-2894     | Hard Washer     | 2     |
6V-5066     | O-Ring Seal     | 1     |
8T-1919     | O-Ring Seal     | 1     |
127-4230     | Seal     | 2     |
388-3917     | Flange     | 1     |
388-6443     | Ring     | 1     |
446-0378     | Tube As     | 1     |
446-0380     | Elbow     | 1     |
Show/hide table
Effective Serial Numbers     |
---|
S/N:TKG00002-UP     |
S/N:TKT00228-UP     |
S/N:TKX00202-UP     |
S/N:TKY00336-UP     |
Rework Procedure
- Drain jacket water coolant into suitable container for reuse or disposal.
- Remove the 390-7470 Elbow and 375-7973 Tube from the engine. Set aside all brackets and hardware for reuse.
Note: Do not remove the water pump flange.
- Install elbow (2) and one O-ring into existing water pump flange.
Show/hide table
Illustration 1 | g03640682 |
(1) 388-6443 Ring (2) 446-0380 Elbow (3) 446-0378 Tube As (4) 388-3917 Flange (5) 0S-1571 Bolt (6) 5M-2894 Hard Washer (7) 8T-1919 O-Ring Seal (8) 6V-5066 O-Ring Seal |
- Install one ring (1) and one O-ring (7) onto tube assembly (3) .
- Insert tube assembly (3) into elbow (2) .
- Secure tube assembly (3) to elbow (2) with one flange (4), two bolts (5), and two washers (6) .
- Attach tube assembly (3) to the 216-2285 Tube Joint with one seal (9) .
Show/hide table
Illustration 2 | g03640680 |
(3) 446-0378 Tube As (9) 127-4230 Seal |
- Reinstall all mounting brackets and hardware loosely.
- Secure all components once reassembled.
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install - Right Side and Left Side
374F Excavator Air Cleaner Dust Valve - Clean/Inspect
390F Excavator Engine Enclosure - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
390F Excavator C18 Engine Supplement Hood - Remove and Install - Clean Emissions Module
C4.4 Marine Generator Set Sea Water Pump Pressure Is Low
390F Excavator Machine Systems Control Valve (Boom Lowering)
UPS 750 Uninterruptible Power Supply System Operational Modes
G3600 A4 Engines Refill Capacities
374F Excavator Lifting and Tying Down the Machine
390F MHPU Mobile Hydraulic Power Unit Machine System Relief Valve (Main)
C27 and C32 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C4.4 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C4.4 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
390F Excavator C18 Engine Supplement Engine Rear Mount - Remove and Install
C175-16 Petroleum Generator Set Engines Control Panel
390F Excavator C18 Engine Supplement Engine - Remove and Install
390F Excavator Fan Guard - Remove and Install - Rear
XQC1600 Power Module Fuel System Primary Filter/Water Separator - Drain
G3306B Generator Sets Model View Illustrations
G3306B Generator Sets Product Description
G3306B Generator Sets Declaration of Conformity