Electronic Control Module (ECM) - Flash Program
执行下述程序,对 Product Link 进行闪存编程。 Product Link 通过闪存编程来升级软件。 Product Link 的闪存编程还必须在 Product Link 更换后进行。 Caterpillar 电子技师(Cat ET)包含程序 WinFlash®。 WinFlash 用来为 Product Link 加载软件。
请参阅系统操作、故障诊断与排除、测试和调整, "配置",以配置以下产品:
- PL121SR
- PL300
注: 有两种通信适配器可用于电子控制模块闪存编程。 可采用 7X-1700 通信适配器 或 171-4400 通信适配器 II 。
PL321SR - 171-4400 Caterpillar 通信适配器 II 硬件连接在机器维修接头和 PC 串行端口或 PC 并行端口间。 为 "Caterpillar 通信适配器 II(RP1210)"配有 Cat ET "通信接口设备"。
PL121SR - 245-7310 串行维修 电缆只用于 PL121SR 无线电系统的配置。
注: 只有 171-4400 Caterpillar 通信适配器 II 用于 PL321SR( PL121SR 加 PL300)系统配置。
注: 不要将 171-4400 Caterpillar 通信适配器 II 用于 PL121SR 系统。
注: 不要将 245-7310 串行维修 电缆用于 PL321SR 系统。
PL121SR 系统
闪存编程 PL121SR 无线电模块
以下步骤说明了 PL121SR 的闪存程序。 仅为无线电系统
- 将笔记本电脑连接到机器上的程序
- 将 245-7310 串行维修 电缆连接到笔记本电脑和机器线束的串行维修接头间。
- 选择菜单栏上的 "Utilities(应用程序)"。
- 从下拉列菜单中选择 "Preference(首选项)"。
- 如果未自动选择 "Communications(通信)"栏,则选择 "Communications(通信)"栏。 单击下拉菜单来扩展菜单。 选择 "Caterpillar Embedded Communication Adaptor(Caterpillar 嵌入通信适配器)"。
Show/hide table
图 1 | g01138570 |
- 选择菜单栏上的 "Service(维修)"。 从下拉菜单中选择 "Product Link Flash(Product Link 闪存)"。
Show/hide table
图 2 | g01138571 |
- 以下屏幕出现后,单击 "Browse(浏览)"。
Show/hide table
图 3 | g01134115 |
"Product Link 闪存"屏幕 |
- 单击对应文件。
Show/hide table
图 4 | g01134116 |
- 单击 "Begin Flash(开始闪存)"。
Show/hide table
图 5 | g01134117 |
"文件屏幕" |
- 以下屏幕出现。
Show/hide table
图 6 | g01134118 |
- 程序"闪存"完成后,以下屏幕应当出现。
Show/hide table
图 7 | g01134121 |
- 单击 "OK(确定)"。
Show/hide table
图 8 | g01134122 |
- "Connect(连接)"图标应当从灰色变为激活状态。 单击工具栏上的 "Connect(连接)"图标返回 Cat ET。 请参阅图 9 内的箭头。 (也可以选择菜单栏上的 "File(文件)",然后单击下拉菜单中的 "Connect(连接)"。)
PL321SR 系统
闪存编程 PL121 无线电模块
WinFlash 用来加载软件。 以下步骤说明了闪存编程 PL300 的过程。
- 选择 "ECM Summary(ECM 汇总)"屏幕。
- 在 PL321 系统内,要想利用 PL300 ECM 闪存 PL121SR(无线电),选择 "Service(维修)"菜单栏后选择 "Subsystem Module Programming(子系统模块编程)"。
Show/hide table
图 9 | g01133998 |
PL300 "系统 ECM 汇总"屏幕 |
- "Subsystem Module Programming(子系统模块编程)"屏幕应当出现。
Show/hide table
图 10 | g01134106 |
"子系统模块编程"屏幕 |
- 单击 "Submodule(子模块)"。
Show/hide table
图 11 | g01134107 |
- 单击 PL121SR 需要加载的正确闪存文件。
Show/hide table
图 12 | g01134109 |
- 单击屏幕右下角的 "Begin Progamming(开始编程)"按钮。
Show/hide table
图 13 | g01134110 |
"文件选择"屏幕 |
- 在"闪存"进行中,以下屏幕应当出现。
Show/hide table
图 14 | g01134111 |
- 程序"闪存"完成后,以下屏幕应当出现。
Show/hide table
图 15 | g01134112 |
- 单击 "OK" 加以确认。
Show/hide table
图 16 | g01134113 |
闪存 PL300 ECM
- 要想将 PL300 ECM 闪存到 PL321 系统内,选择 ECM。
- 选择文件。
Show/hide table
图 17 | g01134819 |
- 单击 "Begin Flash(开始闪存)"。
Show/hide table
图 18 | g01134820 |
- 程序加载中,以下屏幕应当出现。
Show/hide table
图 19 | g01134821 |
Show/hide table
图 20 | g01134822 |
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Engine Oil Bypass Valve
Product Link 121S/300 MID 122 - CID 1251 - FMI 03
Product Link 121S/300 MID 122 - CID 1250 - FMI 09
Product Link 121S/300 MID 122 - CID 0269 - FMI 04
Product Link 121S/300 MID 122 - CID 0269 - FMI 03
Product Link 121S/300 MID 122 - CID 0254 - FMI 12
Product Link 121S/300 MID 122 - CID 0254 - FMI 04
Installation of Heated End Gates{6640} Installation of Heated End Gates{6640}
Product Link 121S/300 MID 122 - CID 0168 - FMI 01
836K Landfill Compactor and 834K Wheel Dozer Machine Systems Push Arms and Blade - Remove and Install
424B Backhoe Loader Axles, Differential and Brakes Axle (Front)
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Oil Filter (Hydraulic Return)
C4.4 Engines for Caterpillar Built Machines Engine Oil Pump
Product Link 121S/300 Electronic Control Module (ECM) - Replace
Product Link 121S/300 Electrical Connector - Inspect
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Diesel Exhaust Fluid Tank
Product Link 121S/300 Wiring Harness (Open Circuit) - Test
Product Link 121S/300 Wiring Harness (Short Circuit) - Test
Product Link 121S/300 Specifications
Product Link 121S/300 System Schematic
Product Link 121S/300 ECM Does Not Communicate with User Interface
994K Wheel Loader Hydraulic System Oil (Implement) (Hydraulic Fan) - Change
C4.4 Engines for Caterpillar Built Machines Piston and Rings
2014/04/24 A Procedure to Install the Cold Weather Cover Group onto Certain 773G, 775G and 777G Off-Highway Trucks is Available {1408, 7155, 7170, 7315, 7610, 7620, 795C}