Product Link 121S/300 Caterpillar


MID 122 - CID 1250 - FMI 09

Usage:

769C 01X
产生此代码的情况:

此代码表示 PL300 和 PL121 间缺少通信。 缺少通信可能由以下原因引起:

  • 利用 PL300 上的旧软件(低于 v3.0)"子模块闪存" PL121

  • PL300 和 PL121 间的线束故障

  • PL121 和 PL300 的硬件故障

注: 在版本低于v3.1 的软件内,如果代码在电源通断循环后清除,请确认 GPS 接收机显示为 "Functional(功能正常)"。 如果 GPS 接收机的状态显示为 "Not Present(不存在)",则缺少通信情况依然存在。

测试步骤 1. 检查 PL300 上的软件版本。

利用 Caterpillar 电子技师(Cat ET)检查 PL300 上的软件版本。 单击 "Service(维修)"后单击 "Submodule Programming(子模块编程)"。

预期结果:

软件版本应当为版本 3.0 或更高版本。

结果:

  • 确定 - 软件版本为版本 3.0 或更高版本。 转至测试步骤 2。

  • 异常 - 软件版本并非版本 3.0 或更高版本。

    修复: 为 PL300 闪存最新版本的软件。 软件版本应当为版本 3.0 或更高版本。 清除诊断代码。

    停止

测试步骤 2. 确认 PL300 到 PL121 的电源。

  1. 利用万用表确认 PL300 到 PL121 的电源。

  1. 将 12-针接头从 PL121 上断开。

  1. 检查插脚 1 和 2 上的电压。

预期结果:

电压应在 11 VDC 和 32 VDC 之间。

结果:

  • 确定 - 电压为 11 VDC 到 32 VDC。 转至测试步骤 3。

  • 异常 - 电压并非 11 VDC 到 32 VDC。

    修复: 检查线束有无损坏。 修理或更换线束。 清除诊断代码。

    停止

测试步骤 3. 利用"已知良好装置"更换 PL121。

利用另一台 PL121 更换 PL121。 更换 Product Link 前,请联系您的 Caterpillar 技术通信员。 请参阅系统操作、故障诊断与排除、测试和调整, "电子控制模块(ECM)- 更换"。

预期结果:

诊断代码应当被清除。

结果:

  • 确定 - 诊断代码已被清除。

    修复: 应当更换 Product Link。 更换 Product Link 前,请联系您的 Caterpillar 技术通信员。 请参阅系统操作、故障诊断与排除、测试和调整, "电子控制模块(ECM)- 更换"。

    停止

  • 异常 - 诊断代码未被清除。 转至测试步骤 4。

测试步骤 4. 更换 PL300。

更换 PL300。

预期结果:

诊断代码应当被清除。

结果:

  • 确定 - 诊断代码已被清除。

    修复: 更换 PL300。 更换 Product Link 前,请联系您的 Caterpillar 技术通信员。 请参阅系统操作、故障诊断与排除、测试和调整, "电子控制模块(ECM)- 更换"。

    停止

  • 异常 - 诊断代码未被清除。

    修复: 重新执行诊断步骤。 如果诊断代码依然存在,请联系 Caterpillar 技术通信员获得帮助。

    停止

Caterpillar Information System:

Product Link 121S/300 MID 122 - CID 0269 - FMI 04
Product Link 121S/300 MID 122 - CID 0269 - FMI 03
Product Link 121S/300 MID 122 - CID 0254 - FMI 12
Product Link 121S/300 MID 122 - CID 0254 - FMI 04
Installation of Heated End Gates{6640} Installation of Heated End Gates{6640}
Product Link 121S/300 MID 122 - CID 0168 - FMI 01
836K Landfill Compactor and 834K Wheel Dozer Machine Systems Push Arms and Blade - Remove and Install
424B Backhoe Loader Axles, Differential and Brakes Axle (Front)
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Oil Filter (Hydraulic Return)
14M3 Motor Grader Machine Systems Air Conditioner and Mounting
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Instrument Panel
424B and 424B HD Backhoe Loaders Hydraulic and Steering System Sideshift Slide Lock Circuit
Product Link 121S/300 MID 122 - CID 1251 - FMI 03
C4.4 Engines for Caterpillar Built Machines Engine Oil Bypass Valve
Product Link 121S/300 Electronic Control Module (ECM) - Flash Program
C4.4 Engines for Caterpillar Built Machines Engine Oil Pump
Product Link 121S/300 Electronic Control Module (ECM) - Replace
Product Link 121S/300 Electrical Connector - Inspect
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Diesel Exhaust Fluid Tank
Product Link 121S/300 Wiring Harness (Open Circuit) - Test
Product Link 121S/300 Wiring Harness (Short Circuit) - Test
Product Link 121S/300 Specifications
Product Link 121S/300 System Schematic
Product Link 121S/300 ECM Does Not Communicate with User Interface
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.