New Radio Software Is Now Available For Product Link 522 and 523 Radio On All Cat ® Products {7610, 7620}
- Caterpillar Products:
- All
Description of Change: The new radio software is now used on all PL522 and 523 radio devices. The new software (PROD_REL- 4.0.2) contains the following enhancements:
- Corrected issue in previous software version (PROD_REL- 4.0.1) where input events on digital inputs 6 and 7 are swapped on radio device
- Corrected issue in which SIM status was intermittently set to an incorrect status of "Not Ready"
- Added wakeup override support in which the device will holdoff shutdown if ignition is off but wakeup override signal is set
- Corrected issue in which digital and ignition events were getting missed
- Improved boot-up to cell connection time
- Corrected issue in which personality reports were missing data
- Added improvements to Radio/Gateway connection
- Added significant web server access time improvements
- Added support for "Number of SIM PIN Entry Attempts Remaining"
- Added Site Entry and Exit reporting when ignition is off
- Corrected issue in which service meter hours (SMH) would not accrue correctly after Engine ON, following an Engine OFF where the device did not go into low-power mode
- Corrected issue of slow-memory leaks causing device restart after several days
- Added protection against loss of system log after power cut to every 60 seconds
- Increased engineering log storage from 3mb to 5mb
- Added serial port configuration to BIT config once-a-day report
- Added various Cat ET cellular status improvements
- Personality report is now sent out after all cell parameters have been received
Adaptable To: The new software PROD_REL - 4.0.2 replaces the old software PROD_REL - 4.0.1 or older. The new radio software is adaptable to all Caterpillar products using a Product Link 522/523 Radio.
Note: The PL522/523 has to be fully updated by updating both the gateway and the radio. The PL522/523 gateway can be updated via Cat ET. The PL522/523 radio is updated Over-the-Air (OTA) only. There is no capability for updating the PL522 or 523 radio Over-the-Wire (OTW) with Cat ET or WinFlash. Upon the release, firmware version PROD_REL- 4.0.2 will be available by request through VisionLink Support ONLY, and it will not be available in SISweb.
Caterpillar Information System:
C18 Marine Engine Belts - Inspect/Adjust/Replace
2014/05/23 New Maintenance Intervals for Certain Tier 4 Interim Engines Operating in Lesser Regulated Countries {1000}
336F XE Excavator Machine System Specifications Relief Valve (Line)
320 GC, 320 and 323 Excavator Machine Systems Specifications Final Drive
320D2 and 323D2 Excavators Machine Systems Specifications Counterweight
Decommissioning Procedure for Permanently Sealed Diaphragm Accumulators {5077} Decommissioning Procedure for Permanently Sealed Diaphragm Accumulators {5077}
2014/08/27 A New Catalytic Converter Group Is Used on Certain 3516C HD Tier 4 Interim Generator Sets {1091}
C18 Marine Engine Coolant Level - Check
C18 Marine Engine Fan Drive Bearing - Lubricate
C18 Marine Engine Belt Tightener - Lubricate
G3600 A4 Engines Engine Shutdown Occurrence
C18 Marine Engine Product Lifting
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554} Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
C18 Marine Engine Radiator - Clean
Priming the Jacket Water Heater System on Certain 3500 and C175 Engines{1383} Priming the Jacket Water Heater System on Certain 3500 and C175 Engines{1383}
2013/12/19 Flywheel UPS Parts Acquisition {1156}
XQ375 and XQ425 Rental Generator Sets Safety Messages
345B Excavator and 345B Material Handler Machine System Specifications Track Roller Mounting
G3600 A4 Engines Electronic Control System Operation
G3600 A4 Engines General Information (Air Inlet and Exhaust System)
G3600 A4 Engines Exhaust Temperature - Test
2013/12/23 New Improved Engine Control Software Is Now Available for Certain T4 Interim C13 Industrial Engines Used in Haliburton ADP Blender Applications {7610, 7620}
C-10, C-12 and C-15 On-Highway Engines Maintenance Interval Schedule - C-10 and C-12 Truck Engines
G3516 TA Engine Engine Shutdown or Start Inhibit Initiated by Driven Equipment