PM-200 Cold Planer Caterpillar


Rotor Drive (Planetary) Oil - Change

Usage:

PM-200 P1C


Note: The rotor drive (planetary) oil drain plug and fill plug are located on the left side of the machine, on the rotor drum frame.




Illustration 1g03438579

  • Turn on the engine and fully raise and lock the left side panel. Turn off the engine.

    1. Use a suitable pry bar in mechanical insert (1) to rotate the rotor manually. Rotate the rotor so that fill plug (2) is aligned with hole (3) on the frame. Remove the drain plug (4) and the fill plug (2) .

    1. Allow the oil to drain in a suitable container. Install the drain plug (4) .

    1. Add clean oil to the hole for the fill plug (2) until the oil level is at the bottom of the opening.

    1. Install the fill plug (2) .


    NOTICE

    Do not under fill or over fill the rotor planetary reducer with oil. Either condition can cause damage to the rotor drive system. Allow enough time for oil to flow through the bearings and reach the correct level in all compartments. Allow more time for cold oil.


  • Caterpillar Information System:

    PM-200 Cold Planer Rotor Drive (Planetary) - Inspect
    131-5051 Dataview Group and Dataview Portable Tech Station Group{0374, 0599, 0701, 0709} 131-5051 Dataview Group and Dataview Portable Tech Station Group{0374, 0599, 0701, 0709}
    PM-200 Cold Planer Rotor Drive Brakes - Inspect/Adjust
    2013/12/23 New Exhaust Shield Assemblies Are Used on Certain 3408 and 3412 Engines {1107}
    PM820, PM822, and PM825 Cold Planer Rotor Drive Belt - Inspect
    PM310, PM312, and PM313 Cold Planer Rotor Coolant Level - Check
    PM-200 Cold Planer Radiator - Clean
    990K Wheel Loader and 844K Wheel Dozer Machine Systems Electrohydraulic Control (Joystick) - Remove and Install
    PM-200 Cold Planer Power Take-Off Clutch Oil Sample - Obtain
    3500 and 3500B High Displacement Engines for Caterpillar Built Machines Vibration Damper - Remove and Install
    PM-200 Cold Planer Power Take-Off Clutch Oil Level - Check
    PM-200 Cold Planer Power Take-Off Clutch Oil Filter - Replace
    PM-200 Cold Planer Rotor Drive (Planetary) Oil Level - Check
    PM820, PM822, and PM825 Cold Planer Rotor Drive (Planetary) Oil Sample - Obtain
    PM-200 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
    PM-200 Cold Planer Rotor Service Door Pivot Pins - Lubricate
    PM-200 Cold Planer Upper Conveyor Belt (Second Stage) Tension and Tracking - Adjust
    2013/10/02 Improvements for Products and Systems Connected to Product Link {7606}
    988K XE Wheel Loader Machine Systems Hydraulic Tank - Disassemble
    988K XE Wheel Loader Machine Systems Piston Pump (Hydraulic Fan) - Disassemble
    988K XE Wheel Loader Machine Systems Piston Pump (Hydraulic Fan) - Assemble
    2013/10/10 A New Plate Assembly is Now Used in the Air Starting Arrangements (If Equipped) on the 793F, and 797F Off-Highway Trucks {5500, 5501, 7516, 7540}
    2013/10/03 The Hydraulic System Has Been Updated on the 797F Off-Highway Trucks {1408, 1439, 430S}
    793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) Payload Monitor (Scoreboard)
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.