C15 and C18 Engines for China On-Highway Phase IV Caterpillar


Aftertreatment Identification Module - Test

Usage:

C18 BE2
表 1 内列出了后处理识别模块的诊断故障代码。

在执行以下步骤之前,使用 Cat 电子技师清除所有"现行"代码。 参考故障排除, "诊断能力 - 清除现行机载诊断(OBD)代码"以了解关于清除"现行"代码的更多信息。

表 1
诊断故障代码    
CDL 代码     J1939 代码     代码说明
(代码说明可能不同)    
注释    
3468-2     5576-2     后处理 #1 识别号模块:不稳定、间歇或不正确     所安装的清洁排放模块(CEM)未经与发动机之间的匹配认证。
此代码是经过确认的排放法规违反代码。 如果不立即解决此问题,可能遭受罚款和/或法律制裁。 不要让发动机带病工作。

发动机功率减额。    
3468-8     5576-8     后处理 #1 识别号模块:异常频率、脉冲宽度或周期     排放不合规。 不要继续让发动机带病工作。

发动机功率减额。    
遵循故障排除步骤来确定故障根源。    

表 2
故障排除测试步骤     数值     结果    

1. 检查有无诊断故障代码

A. 在 Caterpillar 电子技师(ET)和电子控制模块(ECM)之间建立通信。 如有必要,参考故障排除, "电子维修工具"。

B. 在执行任何故障排除或清除诊断故障代码前,从发动机 ECM 下载"保固报告"。
   

诊断故障代码    

结果:诊断代码 3468-2、3468-8、5576-2 或 5576-8 为现行状态。

转至测试步骤 2。
   



图 1g01963854

典型 CEM 识别标牌




图 2g02233953

CEM(典型)

(1) CEM 识别标牌的典型位置

表 3
故障排除测试步骤     数值     结果    

2. 人工输入后处理识别信息

CEM 识别标牌位于电子面板上。
此程序需要出厂密码。

A. 确认发动机上安装了经过认证的 CEM。
请联系您当地的 Caterpillar 代理商,以获得您发动机已批准 CEM 和 RF 配置的清单。

B. 记录 CEM 识别标牌上的 CEM 序列号和配置总成。

C. 确认 CEM 经过与发动机之间的匹配认证。
必要时,联系 Caterpillar 技术通信员。
   

匹配认证    

结果:CEM 经过与发动机之间的匹配认证。

转至测试步骤 3。

结果:CEM 未经过与发动机之间的匹配认证。

拆下 CEM 后利用经过与发动机之间匹配认证的 CEM 加以更换。 关于拆卸和安装步骤,参考拆解和装配。 安装新 CEM 时,"后处理识别号模块"将开始与 ECM 进行通信,并且清除该诊断代码。

在确定 CEM 是否经过匹配认证时:
如果发动机的总工作小时数低于 100,则发动机 ECM 将只与 CEM 通信。 如果小时数大于 100,必须利用 Cat 电子技师将 CEM 识别标牌上的信息编程设定到 ECM 中。
   



图 3g01969939

表 4
故障排除测试步骤     数值     结果    

3. 后处理配置

A. 建立 Cat 电子技师和 ECM 之间的通信。 如有必要,参考故障排除, "电子维修工具"。

B. 导航至 "Aftertreatment Configuration(后处理配置)"页面。

C. 利用 CEM 识别标牌上的序列号编程设定 "Factory Installed Aftertreatment #1 Identification Number(工厂安装的后处理 #1 识别号)"。

D. 利用 CEM 识别标牌上的配置总成编程设定 "DPF #1 Soot Loading Sensing System Configuration Code(DPF #1 烟灰负载感应系统配置代码)"。
   

CEM 配置    

结果:该诊断代码被自动清除。

返回工作。
   

Caterpillar Information System:

C15 and C18 Engines for China On-Highway Phase IV Cooling Fan Control - Test
C15 and C18 Engines for China On-Highway Phase IV Data Link Configuration Status - Test
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Front Screen and Air Filter
C15 and C18 Engines for China On-Highway Phase IV Electrical Power Supply - Test
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies DC Bus Capacitor - Remove and Install
C15 and C18 Engines for China On-Highway Phase IV Ether Starting Aid - Test
C15 and C18 Engines for China On-Highway Phase IV Exhaust Balance Valve - Test
C15 and C18 Engines for China On-Highway Phase IV Fuel Temperature Is High
C15 and C18 Engines for China On-Highway Phase IV Injector Solenoid - Test
C15 and C18 Engines for China On-Highway Phase IV Intake Manifold Air Pressure Is Low
C15 and C18 Engines for China On-Highway Phase IV NOx Reduction System (NRS) - Test
C15 and C18 Engines for China On-Highway Phase IV NRS Exhaust Gas Temperature Is High
C15 and C18 Engines for China On-Highway Phase IV Air Shutoff - Test
C15 and C18 Engines for China On-Highway Phase IV Aftertreatment Cooling Fan - Test
C15 and C18 Engines for China On-Highway Phase IV ARD Nozzle Heater - Test
C15 and C18 Engines for China On-Highway Phase IV ARD Nozzle - Test
C15 and C18 Engines for China On-Highway Phase IV ARD Ignition - Test
C15 and C18 Engines for China On-Highway Phase IV Retarder - Test
C15 and C18 Engines for China On-Highway Phase IV ARD Combustion Air - Test
C13 Generator Set Engine Engine - Remove and Install
C7.1 Industrial Engine Battery or Battery Cable - Disconnect
XQ125 Generator Set Battery or Battery Cable - Disconnect
C4.4 Industrial Engine Belt Tensioner - Check
XQ125 Generator Set Belt - Inspect
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.