794 AC Off-Highway Truck Caterpillar


Automatic Lubrication Reservoir - Fill

Usage:

794 AC HRT

  • Prepare the machine for maintenance. Refer to Operation and Maintenance Manual, "Prepare the Machine for Maintenance".


    Illustration 1g03737602
    Location of Lubrication Reservoir (1)

  • Check the vent valve (2).

    Note: If the reservoir is not properly vented, pressure will cause the wiper seal on the follower assembly inside the reservoir to fail when the reservoir is filled. Grease on the top side of the follower assembly may prevent the autolube system from functioning properly. Also, grease on the top side of the follower assembly may damage the autolube system.

  • Connect hose to port (4).

  • Pull out button switch (5) to the ON position and make sure that lube grease fill switch (6) is in closed state.

  • Fill the reservoir until the light activates on the button switch (5). Float switch (3) is tied to the button switch (5) and determines when the reservoir is full.

    Note: The bulk capacity of the grease reservoir is 54 kg (120 lb).

  • Press the button switch (5) to the OFF position and make sure that lube grease fill switch (6) is in closed state.

  • Remove filler hose.

    The automatic lubrication reservoir provides lubrication for many components. There are fittings at the following locations: rear of machine, left side of machine and right side of machine.

    If any of the remote lines become damaged, install a fitting in place of the remote line. Lubricate the item at the fittings until the remote line can be replaced.

  • Caterpillar Information System:

    XQC1600 Power Module Sound Information
    UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Modbus Register Map
    XQC1600 Power Module Product Description
    PM620 and PM622 Cold Planer Slope Operation
    2013/08/19 New Software Is Now Available For All Cat® Products With PL522 China System {7606, 7620}
    C175-16 Locomotive Engine Flywheel Housing Cover
    C4.4 Industrial Engine Sensors and Electrical Components
    C4.4 Industrial Engine Monitoring System - Engine Indicators and Aftertreatment Indicators
    Procedure for Installing Capacitor Assembly on Certain UPS{4480} Procedure for Installing Capacitor Assembly on Certain UPS{4480}
    2014/05/20 Low Engine Oil Pressure Issues, Oil Pump Failures for C9 and C9.3 Commercial Engines {1304, 1315}
    794 AC Off-Highway Truck Air Conditioner Filter - Clean
    C4.4 Industrial Engine Gauges and Indicators
    794 AC Off-Highway Truck Cab Air Filter - Clean/Replace
    794 AC Off-Highway Truck Engine Air Precleaner - Clean
    794 AC Off-Highway Truck Frame and Body - Inspect
    794 AC Off-Highway Truck Frame and Body Support Pads - Clean/Inspect
    C175-16 Locomotive Engine Exhaust Diffuser Adapter
    C175-16 Locomotive Engine Flywheel
    349F and 352F Excavator Machine System Wiring Harness (Open Circuit) - Test
    349F and 352F Excavator Machine System Wiring Harness (Short Circuit) - Test
    C15 and C18 Engines for China On-Highway Phase IV Event Codes
    C4.4 Industrial Engine Diagnostic Flash Code Retrieval
    349F and 352F Excavators Parking
    C4.4 Industrial Engine Configuration Parameters
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.