C7.1 Engines Caterpillar


Camshaft Position Sensor - Remove and Install

Usage:

525D 2L5

拆卸步骤


注意

在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。

按照本地法规和指令处置所有液体。



注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。




    图 1g03416427

  1. 将锁片 (2) 滑入解锁位置。 将线束组件 (1) 从凸轮轴位置传感器 (3) 上断开。

  2. 拆下螺栓 (4)。 小心地将凸轮轴位置传感器 (3) 从缸体上拆下。

    注: 不要使用杠杆拆卸凸轮轴位置传感器。

  3. 将 O 形密封圈 (5) 从凸轮轴位置传感器 (3) 上拆下。

安装步骤


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。




    图 2g03416427

  1. 将新的 O 形密封圈 (5) 安装到凸轮轴位置传感器 (3) 上。

    注: 不要润滑 O 形密封圈。

  2. 将凸轮轴位置传感器 (3) 安装到缸体上。 安装螺栓 (4) 并用手拧紧螺栓至扭矩为 14 N·m (124 lb in)

  3. 将线束组件 (1) 连接到凸轮轴位置传感器 (3) 上。 将锁片 (2) 滑动到锁定位置。

Caterpillar Information System:

C7.1 Engines Diesel Oxidation Catalyst Has Incorrect Inlet Temperature
3516C Petroleum Engines Hydraulic Starting Motor - Remove and Install
C4.4 Industrial Engine Battery Disconnect Switch
2014/03/14 A New Wiring Harness Is Used in the Dosing Cabinets of Certain 3516C and C175-16 Engines {108H, 1091, 1408}
C15 Petroleum Engines Maintenance Interval Schedule
794 AC Off-Highway Truck Coolant Pressure Cap - Clean/Replace
C175-16 Engine for 795F Series AC Off-Highway Trucks Fuel Priming Pump
C7.1 Industrial Engine Battery Disconnect Switch - If Equipped
399-9725 SCR Catalyst Lifting Device{0629, 0632, 1075, 108H} 399-9725 SCR Catalyst Lifting Device{0629, 0632, 1075, 108H}
3512E Petroleum Engines Hydraulic Starting Motor - Remove and Install
3512C Petroleum Engines Catalyst - Remove and Install
3512E Petroleum Engines Flywheel Housing - Remove
C4.4 Engines Diesel Oxidation Catalyst Has Low Conversion Efficiency
2013/08/06 New Engine Oil Filter for C3.4B Engines {1308}
2013/08/15 New Software For Cat® ET Can Now Be Used For All Caterpillar Products {0785, 7606}
3500 Engines Engine Oil Cooler - Disassemble
3500 Engines Engine Oil Cooler - Assemble
2013/09/16 New Wiring Harness Film Is Used for the Pre-lubrication Pump on Certain G3500 Engines {1319, 1408}
C7.1 Industrial Engine Diesel Exhaust Fluid - Fill
2013/09/20 A New and Improved Switch and Contactor Are Used for the Jacket Water Heater Control on Certain 3512C Engines {1383, 1408, 1408}
C15 and C18 Engines for China On-Highway Phase IV Diagnostic Capabilities
349F and 352F Excavators Leaving the Machine
C7.1 Industrial Engine Injector (Diesel Exhaust Fluid) - Replace
C13 Generator Set Engine Exhaust Manifold - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.