Catalyst (SCR) - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 352-5891 | 吊带 | 2 |
B | - | Loctite 771 | - |
开始:
- 拆卸催化器进口温度传感器。
Show/hide table
高温发动机部件可能导致灼伤。 进行发动机保养之前让发动机和部件冷却下来。 |
Show/hide table
在处理用过的柴油微粒滤清器或催化转化器消声器时,请配戴护目镜、手套、防护服以及经过职业安全与健康管理局(NIOSH)批准的 P95 或 N95 半面式防尘面罩。 否则可能造成人身伤害。 |
- 松开卡箍组件 (1)。
- 断开卡箍组件 (2)。
- 使用工具 (A) 拆卸催化器 (SCR) (3)。 催化器 (SCR) (3) 的重量约为
53 kg (117 lb) 。Show/hide table图 2 g03386045 - 松开带箍 (5),然后拆下波纹管组件 (4)。
- 废弃带箍 (1) 和 (5)。
Show/hide table
图 1 | g02849252 |
注: 当安装新的催化器或清洁后的催化器时,必须执行 SCR 复位。 有关正确的步骤,请参阅专门说明书, REHS8180, "后处理 - 对配备柴油微粒滤清器(DPF)、柴油氧化催化剂(DOC)和选择性催化还原(SCR)滤清器"的 Tier 4 Final 产品进行滤清器的保养。
- 按与拆卸相反的顺序安装催化器 (SCR) (3)。
- 沿距离 (X )向卡箍组件 (2) 的螺纹上涂覆工具 (B)。 距离 (X) 高出耳轴
25 mm (1 in) 。 将卡箍组件 (2) 拧紧至扭矩为16.5 ± 1.5 N·m (146 ± 13 lb in) 。Show/hide table图 4 g03386044 带箍 (1) 和 (5) 在组件上就位的剖视图。 注: 不要使用电动工具拧紧带箍 (1)、和 (5)。
- 确认球头 (G) 的球头座不接触球 (F) 的半径。 定位带箍 (1) 和 (5),手动拧紧带箍 (1) 和 (5)。 带箍 (1) 和 (5) 应处于接头中央。
- 尺寸 (C) 和尺寸 (D) 之间的差值应当在
2.0 mm (0.08 in) 的范围内。 环绕带箍 (1) 和 (5) 每隔 90° 重复测量一次。 如有必要,调整带箍 (1) 和 (5)。 - 将带箍 (1) 和 (5) 拧紧至扭矩为
35 ± 2 N·m (26 ± 1 lb ft) 。
Show/hide table图 3 g02849250 典型示例 注: 切勿使用电动工具拧紧卡箍组件 (2)。
- 沿距离 (X )向卡箍组件 (2) 的螺纹上涂覆工具 (B)。 距离 (X) 高出耳轴
Caterpillar Information System:
C32 Generator Set Fuel Related Components in Cold Weather
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Manifold (DEF Heater) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electronic Control (Diesel Exhaust Fluid) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Filter - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Assemble
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector - Remove and Install
3500 Generator Sets Product Description
374F Excavator Monitoring System
424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202} 424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202}
2013/07/08 New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
C15 and C18 Engines for Caterpillar Built Machines Nitrogen Oxide Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
3516C Petroleum Engines Engine Oil Cooler - Remove and Install
C175-16 Engine for 795F Series AC Off-Highway Trucks Fuel Injection Pump
794 AC Off-Highway Truck Engine Air Filter Primary Element - Clean/Replace
794 AC Off-Highway Truck Window Wiper - Inspect/Replace
794 AC Off-Highway Truck Windows - Clean
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install - Remote Mounted