Manifold (DEF Heater) - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 207-1601     | 橡胶润滑剂     | -     |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 钳断软管 (3) 。
Show/hide table
图 1 | g03375189 |
注: 请参阅专门说明书, REHS8231, "柴油机排气处理液 (DEF) 接头的拆卸步骤",了解软管组件 (4) 的正确拆卸步骤。
- 拆下夹子 (1) 和 (5) 。 断开线束组件 (2) 。 拆下软管组件 (4) 和软管 (3) 。
- 拆下电缆带 (6) ,然后断开线束组件 (7) 。
Show/hide table
图 2 | g03375204 |
- 拆下螺栓 (8) 、板 (9) 、歧管 (10) 和垫片(未显示)。
Show/hide table
图 3 | g03375207 |
- 将滤清器组件 (11) 从歧管组件 (10) 上拆下。
Show/hide table
图 4 | g03382988 |
箭头指示滤清器组件 (11) 的拆卸方向。 |
Show/hide table
图 5 | g03375411 |
注: 要将滤清器组件 (11) 从歧管组件 (10) 上拆下,拉出锁片 (12) 。
安装步骤
- 按照与拆卸相反的顺序安装歧管 (10) 。
- 按照交替顺序拧紧螺栓 (8) 至扭矩为 5 ± 1 N·m (44 ± 9 lb in)。 按照交替顺序再次拧紧螺栓 (8) 至扭矩为 5 ± 1 N·m (44 ± 9 lb in)。
- 将工具 (A) 涂覆到软管组件 (5) 内的 O 形密封圈上。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Electronic Control (Diesel Exhaust Fluid) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Filter - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Assemble
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector - Remove and Install
WS223, WS223 SS, WS223 XD, WS255, WS255 SS, WS255 XD, WSP223, WSP255, WSF223, WSF223 SS, WSF223 XD, WSF255, WSF255 SS and WSF255 XD Well Stimulation Pumps Flange (Discharge) - Remove and Install
2013/06/18 A New Jumper Harness Is Now Installed on Certain C32 Marine Engine Harnesses {1408}
C7.1 Marine Generator Set Reference Material
C15 and C18 Engines for Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
2013/06/13 New Injection Assemblies Are Equipped with Flow Indicators for Certain Retrofit Selective Catalytic Reduction Systems {108I}
C15 and C18 Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C32 Generator Set Fuel Related Components in Cold Weather
C15 and C18 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install
3500 Generator Sets Product Description
374F Excavator Monitoring System
424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202} 424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202}
2013/07/08 New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
C15 and C18 Engines for Caterpillar Built Machines Nitrogen Oxide Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
3516C Petroleum Engines Engine Oil Cooler - Remove and Install