Diesel Exhaust Fluid Module - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 207-1601 | 橡胶润滑剂 | - |
- 安装 O 形密封圈(未显示)和接头 (46)。
Show/hide table
图 2 g03366053 - 安装线束组件 (44) 和电缆扎带 (45)。
Show/hide table
图 3 g03366046 注: 不要在螺栓 (41) 上使用冲击扳手。
- 将泵 (43) 安装在支承组件 (42) 中。 安装螺栓 (41)。 拧紧螺栓 (41) 至扭矩为
19 ± 2 N·m (168 ± 18 lb in) 。Show/hide table图 4 g03366035 - 连接线束组件 (40)。
Show/hide table
图 5 g03366015 注: 不要在螺栓 (39) 上使用冲击扳手。
- 安装支架 (37)、螺栓 (39) 和电缆扎带 (38)。
Show/hide table
图 6 g03383610 - 安装滤清器 (36)。
Show/hide table
图 7 g03383609 - 安装扩展设备 (35)。
Show/hide table
图 8 g03383608 - 安装盖 (34)。 将盖 (34) 拧紧至扭矩为
20 ± 5 N·m (177 ± 44 lb in) 。Show/hide table图 9 g03365554 - 安装电子控制装置 (31)。 安装电缆扎带 (32) 并连接线束组件 (33)。
Show/hide table
图 10 g03365547 - 安装控制模块 (30)。 将螺栓 (29) 拧紧至扭矩为
10 ± 2 N·m (89 ± 18 lb in) 。Show/hide table图 11 g03365540 注: 不要在继电器 (28) 的螺栓上使用冲击扳手。
- 安装继电器 (28)。
Show/hide table
图 12 g03365528 注: 不要在电磁阀组件 (27) 的螺栓上使用冲击扳手。
- 安装电磁阀组件 (27)。 连接线束组件 (26)。
Show/hide table
图 13 g03365521 - 将螺塞 (24) 和 (25) 安装到歧管 (22) 上。 将 O 形密封圈 (23) 安装在盖 (21) 中。
Show/hide table
图 14 g03365514 注: 不要在螺栓 (19) 上使用冲击扳手。
- 安装歧管 (20)。 安装螺栓 (19)。 安装盖 (17)。 安装螺栓 (18)。 拧紧螺栓 (18) 至扭矩为
6 ± 1 N·m (53 ± 9 lb in) 。Show/hide table图 15 g03365493 - 将支架 (16) 安装到油箱上。 安装螺栓 (15 )。
Show/hide table
图 16 g03365477 - 安装泵组件 (14 )和螺栓 (13)。
Show/hide table
图 17 g03365475 注: 不要在螺栓 (12) 上使用冲击扳手。
- 安装螺栓 (12)。 将螺栓 (12) 拧紧至扭矩为
4 ± 1 N·m (35 ± 9 lb in) 。Show/hide table图 18 g03365468 - 安装螺栓 (11)。
Show/hide table
图 19 g03365465 - 安装垫片(未显示)、歧管 (10)、板 (9) 和螺栓 (8)。 按照交替顺序拧紧螺栓 (8) 至扭矩为
5 ± 1 N·m (44 ± 9 lb in) 。 按照交替顺序再次拧紧螺栓 (8) 至扭矩为5 ± 1 N·m (44 ± 9 lb in) 。Show/hide table图 20 g03365463 - 连接线束组件 (7) ,然后安装电缆带 (6)。
Show/hide table
图 21 g03365452 注: 不要在夹子 (1) 和 (5) 的螺栓上使用冲击扳手。
- 安装软管 (3)。 将工具 (A) 涂覆到软管组件 (4) 内的 O 形密封圈(未显示)上。 连接软管组件 (4)。 连接线束组件 (2)。 安装夹子 (1)。 将夹子 (1) 的螺栓拧紧至扭矩为
6 ± 1 N·m (53 ± 9 lb in) 。 安装夹子 (5)。Show/hide table图 22 g03350789 Show/hide table图 23 g03376333 - 将油箱 (48) 安装在支承组件 (49) 中。 安装扎带 (50)。 安装螺母 (51)。 拧紧螺母 (51) 至扭矩
8 ± 2 N·m (71 ± 18 lb in) 。 拧紧螺母 (51) 至最终扭矩为11 ± 1 N·m (97 ± 9 lb in) 。注: 拧紧扎带 (50) 时,只拧紧螺母 (51) 一次。 按图 23 中所示的 W、X、Y、Z 顺序拧紧螺母 (51)。
注: 使用两种类型的扎带来支撑不同的油箱配置。 只拧紧两种类型扎带上的螺母一次。
Show/hide table图 24 g03349224 - 安装支架 (46)。 安装软管组件 (47)。
Show/hide table
图 1 | g03366057 |
注: 拆卸后,必须将接头 (46) 装回原位。 接头 (46) 不可互换。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector - Remove and Install
WS223, WS223 SS, WS223 XD, WS255, WS255 SS, WS255 XD, WSP223, WSP255, WSF223, WSF223 SS, WSF223 XD, WSF255, WSF255 SS and WSF255 XD Well Stimulation Pumps Flange (Discharge) - Remove and Install
2013/06/18 A New Jumper Harness Is Now Installed on Certain C32 Marine Engine Harnesses {1408}
C7.1 Marine Generator Set Reference Material
C15 and C18 Engines for Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
2013/06/13 New Injection Assemblies Are Equipped with Flow Indicators for Certain Retrofit Selective Catalytic Reduction Systems {108I}
C175-16 Locomotive Engine Engine Oil Temperature Sensor
C32 Generator Set Voltage Regulators - R450T Automatic Voltage Regulator (AVR)
C7.1 Industrial Engine Product Storage
C13, C15, and C18 Tier 4 Final Engines Coolant Level Sensor
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Filter - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electronic Control (Diesel Exhaust Fluid) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Manifold (DEF Heater) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C32 Generator Set Fuel Related Components in Cold Weather
C15 and C18 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install
3500 Generator Sets Product Description
374F Excavator Monitoring System
424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202} 424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202}