Piston Cooling Jets - Remove and Install
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 9S-9082 | 发动机盘车工具 | 1 |
开始:
- 拆下发动机机油泵。
Show/hide table
| 注意 |
|---|
|
特别小心不要使活塞冷却喷嘴弯曲，因为活塞冷却喷嘴是精确对准活塞冷却液通道的。 每个冷却喷嘴仅有一个位置。 活塞在下止点时，活塞底部的挡圈使活塞冷却喷嘴有间隙。 |
- 使用工具 (A)转动曲轴，以便可以接近活塞冷却喷嘴。
- 拆下螺栓 (1) 和活塞冷却喷嘴 (2)。
Show/hide table
| |
| 图 1 | g01004705 |
Show/hide table
| 注意 |
|---|
|
特别小心不要使活塞冷却喷嘴弯曲，因为活塞冷却喷嘴是精确对准活塞冷却液通道的。 每个冷却喷嘴仅有一个位置。 活塞在下止点时，活塞底部的挡圈使活塞冷却喷嘴有间隙。 |
- 按与拆卸相反的顺序安装活塞冷却喷嘴 (2)。
- 将螺栓拧紧至扭矩为
40 ± 8 N·m (30 ± 6 lb ft)
- 将螺栓拧紧至扭矩为
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Cylinder Liner - Remove and Install
C175 Commercial Engine Intake Valve Recession {1100} C175 Commercial Engine Intake Valve Recession {1100}
2013/08/06 New Software Is Now Used on Certain C18 Auxiliary and Generator Set Engines {1920}
C15 and C18 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
C18 Generator Set Model View Illustrations
C13 and C15 Generator Sets After Starting Engine
C7.1 Marine Generator Set Welding on Engines with Electronic Controls
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set System Pressure Release
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Assemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C15 and C18 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove and Install
C7.1 Marine Generator Set Aftercooler Condensate Drain Valve - Inspect/Clean
C15 and C18 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
C7.1 Marine Generator Set Battery or Battery Cable - Disconnect
C15 and C18 Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install