Cylinder Liner - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 5P-8665(1) | 缸套拉拔器总成 | 1 |
B | 2P-8260 | 缸套安装器 | 1 |
C | 5P-3975 | 橡胶润滑剂 | 1 |
Show/hide table
(1) | 6V-9448 气缸组件拉拔器是 |
开始:
- 拆下活塞和连杆。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 利用工具 (A) 拆下缸套 (1)。
Show/hide table
图 1 | g01005579 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查缸套突出量。 请参阅测试和调整, "缸套突出量 - 检查"。
Show/hide table
图 2 g01004993 - 将缸套密封件 (3) 装入对应环槽中。
- 缸套孔表面和缸套密封件上 (3) 使用工具 (C)。
- 把加注口带箍 (2) 在清洁的发动机机油中浸泡一会儿。 安装加注口带箍 (2) 后立即安装缸套 (1)。
Show/hide table
图 3 g01005003 - 使用工具 (B) 来把缸套 (1) 安装到缸体中。 确保一切与缸套凸出量有关的标记都要校准。
注: 关于缸套安装方面的更多信息,请参阅专门说明书, SEHS9564。
结束:
- 安装活塞和连杆。
Caterpillar Information System:
C175 Commercial Engine Intake Valve Recession {1100} C175 Commercial Engine Intake Valve Recession {1100}
2013/08/06 New Software Is Now Used on Certain C18 Auxiliary and Generator Set Engines {1920}
C15 and C18 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
C18 Generator Set Model View Illustrations
C13 and C15 Generator Sets After Starting Engine
C7.1 Marine Generator Set Welding on Engines with Electronic Controls
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set System Pressure Release
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Assemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C15 and C18 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove and Install
C7.1 Marine Generator Set Aftercooler Condensate Drain Valve - Inspect/Clean
C15 and C18 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
C7.1 Marine Generator Set Battery or Battery Cable - Disconnect
C15 and C18 Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install