Camshaft Bearings - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 8S-2241 | 凸轮轴轴承工具总成 | 1 |
B | 9U-7222 | 凸轮轴轴承导向器 | 1 |
8M-8778 | 拔梢锁紧双头螺柱 1/2 - 13 x 1 9/16 in |
1 | |
C | 9U-7210 | 拉拔器板 | 1 |
D | 9U-7223 | 校准衬套 | 1 |
E | 9U-7213 | 备用板 | 1 |
0S-1621 | 螺栓 1/2 - 13 x 1 in |
1 | |
F | 9U-7214 | 间隔板 | 1 |
开始:
- 拆下凸轮轴。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下 7 号凸轮轴轴承(后部)。 按从发动机后部到前部的顺序操作。
- 把工具 (B) 小的一端安装到凸轮轴轴承 (1) 中。
- 把工具 (C) 置于工具 (A) 的上方。 通过缸盖,把工具 (A) 安装到工具 (B) 上。
注: 工具 (C) 安装到缸盖外面。 需要用到工具 (C) 来从缸盖上拆下所有的凸轮轴轴承。
- 使用工具 (A) 将凸轮轴轴承 (1) 从缸盖上拆下。
- 将工具 (B) 从工具 (A) 上拆下,然后拆下凸轮轴轴承。
Show/hide table
图 1 | g01159745 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 按照以下步骤安装 7 号凸轮轴轴承(后部)。
- 把工具 (B) 大的一端插入 7 号凸轮轴孔。
- 把工具 (C) 置于工具 (A) 的上方。 通过缸盖,把工具 (A) 安装到工具 (B) 上。
- 将凸轮轴轴承 (1) 安置在工具 (B) 上。 将工具 (E) 安装到工具 (B) 上。
注: 请参阅技术规格, "缸盖"以了解缸盖中凸轮轴轴承朝向的相关信息。
- 用工具 (A) 把凸轮轴轴承 (1) 推入凸轮轴孔。
注: 当工具 (E) 的斜面和凸轮轴孔面吻合时,说明凸轮轴轴承安装正确。
Show/hide table图 3 g01159756 - 按照以下步骤安装 6 号 到 2 号凸轮轴轴承:
- 把工具 (B) 大的一端插入凸轮轴孔。
注: 用工具 (D) 校准工具 (A) 和工具 (B) 与凸轮轴轴承孔的位置。 在工具 (A) 和工具 (B) 之间任何一个安装好的的凸轮轴轴承的内径里安装工具 (D)。
- 将工具 (A) 安装在工具 (B) 上。 将凸轮轴轴承 (1) 安置在工具 (B) 上。 将工具 (E) 安装到工具 (B) 上。
注: 请参阅技术规格, "缸盖"以了解缸盖中凸轮轴轴承的位置和朝向的相关信息。
- 用工具 (A) 把凸轮轴轴承 (1) 推入凸轮轴孔。
注: 当工具 (E) 的斜面和凸轮轴孔面吻合时,说明凸轮轴轴承安装正确。
Show/hide table图 4 g01159758 - 把工具 (B) 大的一端插入凸轮轴孔。
- 按照以下步骤安装 1 号凸轮轴轴承(前部):
- 把工具 (B) 大的一端插入 1 号凸轮轴孔。 把工具 (A) 和工具 (D) 组装到工具 (B) 上。
- 将凸轮轴轴承 (1) 安置在工具 (B) 上。 把工具 (E) 和工具 (F) 安装到工具 (B) 上。
注: 请参阅技术规格, "缸盖"以了解缸盖中凸轮轴轴承的位置和朝向的相关信息。
注: 工具 (F) 用于将 1 号凸轮轴轴承座入凸轮轴孔正确深度。
- 使用工具 (A) 将 1 号凸轮轴轴承拉入 1 号凸轮轴孔。 当工具 (E) 的斜面和凸轮轴孔面吻合时,说明凸轮轴轴承安装正确。
Show/hide table
图 2 | g01159754 |
结束:
- 安装凸轮轴。
Caterpillar Information System:
C18 Generator Set Model View Illustrations
C13 and C15 Generator Sets After Starting Engine
C7.1 Marine Generator Set Welding on Engines with Electronic Controls
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set System Pressure Release
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Assemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Gear Group (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
2013/08/06 New Software Is Now Used on Certain C18 Auxiliary and Generator Set Engines {1920}
C175 Commercial Engine Intake Valve Recession {1100} C175 Commercial Engine Intake Valve Recession {1100}
C15 and C18 Engines for Caterpillar Built Machines Cylinder Liner - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C15 and C18 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove and Install
C7.1 Marine Generator Set Aftercooler Condensate Drain Valve - Inspect/Clean
C15 and C18 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install