C15 and C18 Engines for Caterpillar Built Machines Caterpillar


Inlet and Exhaust Valve Guides - Remove and Install

Usage:

826K 232

拆卸步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
(1)     9U-6895     气门导管冲头     1    
(1)     9U-6894     导向圈     1    
C     455-0128     密封件安装工具     1    
( 1 ) 9U-7530 发动机工具总成 的部分工具

开始:

  1. 拆下进气门和排气门。


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。





    图 1g01073841

  1. 从气门导管 (2) 上拆下气门杆密封 (1) 。

  1. 使用工具 (A) 和锤子从缸盖上拆下气门导管。

安装步骤


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。





图 2g01073842

  1. 用清洁的发动机机油润滑气门导管的孔。

  1. 用工具 (A) 和工具 (B) 将气门导管 (2) 安装到缸盖中。

    注: 必须使用工具 (B) 将气门导管安装到正确高度。

    从缸盖表面到气门导管顶部的高度 ... 35.00 ± 0.50 mm (1.378 ± 0.020 in)

    注: 有关详细信息,请参阅规格缸盖, "气门"。

  1. 使用工具 (C) 将气门杆密封圈 (1) 安装在气门导管上。

End By: 安装进气门和排气门。

Caterpillar Information System:

C7.1 Marine Generator Set Engine Operation
C18 Generator Set Safety Messages
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C7.1 Industrial Engine Electrical System
C7.1 Marine Generator Set Starting with Jump Start Cables
C7.1 Marine Generator Set Starting the Engine
C13 and C15 Generator Sets Plate Locations and Film Locations
C15 and C18 Engines for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
2014/06/20 J1939 Suspect Parameter Numbers for G3300B and CG137 Engines {1900, 1901, 1920}
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install
C13 and C15 Generator Sets Product Installation
C7.1 Marine Generator Set Generator Operation
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
2013/06/13 New Fuel Lines Are Available on Certain C18 Marine Engines {1274}
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Assemble
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.