Inlet and Exhaust Valves - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 5S-1330 | 气门弹簧压缩器 | 1 |
B | 8S-2263 | 弹簧测试仪 | 1 |
开始:
- 拆下缸盖。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 安装工具 (A) 并压缩气门弹簧。 将气门弹簧卡座 (2) 从气门 (1) 上拆下。
- 将工具 (A) 从气门 (1) 上缓慢拆下。
- 拆下气门旋转器 (3)。
- 将外气门弹簧 (5) 和内气门弹簧 (4) 从气门 (1) 上拆下。
- 将垫圈 (6) 和气门 (1) 从气门导管上拆下。
- 用工具 (B) 检查一下气门弹簧(弹力)。 关于气门弹簧的更多信息,请参考技术规格, "缸盖气门"。
- 检查每个气门。 关于进气和排气气门的更多信息,请参考技术规格, "缸盖气门"。
Show/hide table
图 1 | g01015263 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 按相反顺序安装进气和排气门。
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
Show/hide table
当松开气门弹簧压缩器的时候,气门弹簧卡座会从气门中弹出。 保证气门弹簧卡座正确安装在气门推杆上。 为了防止造成人员伤害,在安装气门时,应远离气门弹簧卡座前方和气门弹簧。 |
Caterpillar Information System:
C7.1 Industrial Engine Electrical System
C7.1 Marine Generator Set Starting with Jump Start Cables
C7.1 Marine Generator Set Starting the Engine
C13 and C15 Generator Sets Plate Locations and Film Locations
C15 and C18 Engines for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
2014/06/20 J1939 Suspect Parameter Numbers for G3300B and CG137 Engines {1900, 1901, 1920}
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install
C13 and C15 Generator Sets Product Installation
3512C Petroleum Engines with Dynamic Gas Blending Engine Control Switch - Test
2013/07/01 New Flywheel Housing Assemblies and Gaskets Are Used on Certain 3500 Locomotives Engines {1157, 7555}
C13 and C15 Generator Sets Product Lifting
C18 Generator Set Safety Messages
C7.1 Marine Generator Set Engine Operation
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C7.1 Marine Generator Set Generator Operation
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
2013/06/13 New Fuel Lines Are Available on Certain C18 Marine Engines {1274}