C13, C15, and C18 Tier 4 Final Engines Caterpillar


Turbocharger

Usage:

826K 232


图 1g02608142


图 2g02608141

表 1
230-7911 涡轮增压器总成的技术规格 
项目  数量  零件  技术规格说明 
9N-2038 涡轮卡箍组件  按照以下步骤拧紧涡轮卡箍组件:
1. 拧紧至扭矩为 18.0 ± 1.6 N·m (159.3 ± 14.2 lb in)
2. 松开 1 到 2 圈。
3. 再次拧紧至扭矩为 13.6 ± 1.2 N·m (120.4 ± 10.6 lb in)。 
废气旁通阀的开启压力为 142.0 ± 3.5 kPa (20.6 ± 0.5 psi)。 
7W-2297 卡箍组件  拧紧至扭矩为 13.6 ± 1.2 N·m (120.4 ± 10.6 lb in)。 
2N-2766 锁紧螺母  在装配前,向锁紧螺母的螺纹上涂覆 Loctite C5A 铜防咬合剂。 
拧紧至扭矩为 70 ± 5 N·m (52 ± 4 lb ft)

Caterpillar Information System:

C13 Engine for Caterpillar Built Machines Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
Procedure to Install A New Mounting Bracket Group for the Air Compressor on Certain C-18 Commercial Engines{1803} Procedure to Install A New Mounting Bracket Group for the Air Compressor on Certain C-18 Commercial Engines{1803}
Caterpillar Off-Highway Truck (777, 785, 789, 793, and 797) Technician Checklist Final Drive Removal and Installation {0372, 0374, 4001, 4001, 4011, 4011, 4050, 4050} Caterpillar Off-Highway Truck (777, 785, 789, 793, and 797) Technician Checklist Final Drive Removal and Installation {0372, 0374, 4001, 4001, 4011, 4011, 4050, 4050}
Water Delivery System and 777F WTR, 777G WTR and 785D WTR OEM Off-Highway Trucks Display Module Software - Install
Troubleshooting for Caterpillar Well Stimulation Pumps {5070} Troubleshooting for Caterpillar Well Stimulation Pumps {5070}
C7.1 Marine Generator Set General Hazard Information
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply DC Bus Capacitor - Remove and Install
Water Delivery System and 777F WTR, 777G WTR and 785D WTR OEM Off-Highway Trucks Error and Warning Messages
Water Delivery System and 777F WTR, 777G WTR and 785D WTR OEM Off-Highway Trucks Machine Preparation for Troubleshooting
C7.1 Marine Generator Set Generator Isolating for Maintenance
C7.1 Marine Generator Set Engine Electronics
C7.1 Marine Generator Set Engine Starting
Installation of a Dual Tapered Roller Bearing HEUI Hydraulic Pump onto Certain C7 ACERT Engines {1714} Installation of a Dual Tapered Roller Bearing HEUI Hydraulic Pump onto Certain C7 ACERT Engines {1714}
Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC) and a Selective Catalyst Reduction (SCR) Filter {108F} Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC) and a Selective Catalyst Reduction (SCR) Filter {108F}
C15 and C18 Tier 4 Final Engines Clean Emissions Module
2013/06/06 An Alternate Fuel Line Is Available For Certain C18 Marine Engines {1274}
2013/06/03 New Fuel Lines Kits Are Used on Certain C9.3 Industrial Engines {1288}
2013/06/11 A New Prechamber and Gasket Are Available for Certain G3600 Engines {1106}
C9.3 Engines for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052} C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052}
2013/07/22 New Exhaust Manifold Groups Are Available for Certain 3512C Petroleum Engines {1059}
Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822} Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822}
C13 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.