Engine Oil Pressure Sensor - Remove and Install
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
|
在检查, 保养, 测试, 调整 and 维修发动机时，务必留心，确保将溢出的液体盛装在容器中。在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 将锁片 (2) 滑入解锁位置。 将线束组件 (1) 从发动机机油压力传感器 (3) 上断开。
- 用深孔套筒将发动机机油压力传感器 (3) 从缸体上拆下。
- 将 O 形密封圈 (4) 从发动机机油压力传感器 (3) 上拆下。
Show/hide table
| |
| 图 1 | g02315394 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将新 O 形密封圈 (4) 安装到发动机机油压力传感器 (3) 上。
注: 不要润滑 O 形密封圈。
- 用深孔套筒将发动机机油压力传感器 (3) 安装到缸体上。 拧紧发动机机油压力传感器至扭矩为
10 N·m (89 lb in) 。 - 将线束组件 (1) 连接到发动机机油压力传感器 (3) 上。
- 将锁片 (2) 滑动到锁定位置。
- 如有必要，加注发动机油底壳至发动机油尺上指示的正确油位。 有关正确的步骤，参考操作和保养手册, "发动机机油油位 - 检查"。
Show/hide table
|
| |
| 图 2 | g02315394 |
Caterpillar Information System:
C7.1 Engines Engine Oil Pan - Remove - Aluminum Oil Pan
C7.1 Engines Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Engines Engine Oil Filter Base - Remove and Install
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Electronic Unit Injector - Remove
C7.1 Engines Electronic Unit Injector - Install
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Internal Component Preremoval Steps (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Information (Input/Output Cabinet)
C280-16 Engine Fluid Recommendations
C7.1 Engines Engine Oil Pump - Install
C7.1 Engines Engine Oil Pump - Remove
C7.1 Engines Exhaust Elbow - Remove and Install
C7.1 Engines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C7.1 Engines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C7.1 Engines Fan - Remove and Install
C7.1 Engines Fan Drive - Remove and Install
C7.1 Engines Flow Control Valve - Remove and Install
C7.1 Engines Flywheel - Install - Equipped with Rear Power Take-Off
C7.1 Engines Flywheel - Install
C7.1 Marine Engine Engine Oil Filter Base - Remove and Install - Non M.C.S. Arrangement
C7.1 Engines Flywheel - Remove - Equipped with Rear Power Take-Off