Always Purge the Air From the Engine Cooling System {1350, 1353}
- Engine:
- All 3500 Engines
- 3412C (S/N: DJN1-UP; RTY1-UP)
- C9 (S/N: X3R1-UP)
- G3412 SI (S/N: KAP1-UP)
- Generator Set:
- C15 (S/N: C5E1-UP; C5H1-UP; C5L1-UP)
- C18 (S/N: EKW1-UP; M1Z1-UP)
- C27 (S/N: DWB1-UP)
- C32 (S/N: SXC1-UP; JSJ1-UP)
- C32 (S/N: RNX1-UP)
- C9 (S/N: C9E1-UP)
- C175-16 (S/N: WYB1-UP)
- Industrial Engine:
- C27 (S/N: TWM1-UP)
- Marine Engine:
- C32 (S/N: RNY1-UP; RNZ1-UP)
- Power Module:
- PM3516 (S/N: NAM1-UP)
- All 3500 Engines
After filling the engine cooling system, remove the filler cap and run the engine a minimum of 5 minutes after the thermostats have opened.
Running the engine will allow trapped air to be sufficiently purged from the cooling system and allow the cooling system level to stabilize.
Check the coolant level and add coolant if necessary.
Caterpillar Information System:
C7.1 Industrial Engine Model View Illustrations
C4.4 Industrial Engine Welding on Engines with Electronic Controls
C4.4 Industrial Engine Engine Electronics
C27 Generator Set Fluid Recommendations
Procedure for Installing the New Unit Injector Hydraulic Pump Group on Certain C9 Marine Engines{1714} Procedure for Installing the New Unit Injector Hydraulic Pump Group on Certain C9 Marine Engines{1714}
C27 Generator Set Refill Capacities
TA2 Inspection for C32 Marine Propulsion Engines{1000} TA2 Inspection for C32 Marine Propulsion Engines{1000}
2013/03/22 A New Coupling Assembly Is Used on Heat Exchangers for Certain 3512C and 3516C Engines {1379, 7553}
2013/02/18 New Electronic Thermostats Are Used for C175 Engines {135V, 7610}
3516C HD Petroleum Well Service Engines Sensor Signal (Analog, Active) - Test
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Data Link Configuration Status - Test
C7.1 Industrial Engine Electrical System
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Water Valve
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Water Pump
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Hydraulic Tank
C7.1 Industrial Engine Product Description
C4.4 and C7.1 Engines Exhaust Has Excessive Black Smoke
C3.8 Engines for Caterpillar Built Machines Turbocharger - Inspect
C8.7 and C12.9 Marine Engines Exhaust Has Excessive White Smoke
Loader and Excavator Bucket Base Edge Assembly Welding Requirements {0679, 6001, 6101, 6102, 6103, 6104, 6110, 6112, 6120, 6122, 6138, 6503, 6523, 6530, 6800, 6801, 6823} Loader and Excavator Bucket Base Edge Assembly Welding Requirements {0679, 6001, 6101, 6102, 6103, 6104, 6110, 6112, 6120, 6122, 6138, 6503, 6523, 6530, 6800, 6801, 6823}
C7.1 Marine Engine Camshaft Bearings - Remove and Install
C7.1 Marine Engine Engine Oil Pan Plate - Remove and Install
C7.1 Marine Engine Piston Cooling Jets - Remove and Install
C7.1 Marine Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position