398-9680 Calibration Test Group{0599, 0706, 1250, 1251, 1252, 1280} Caterpillar


398-9680 Calibration Test Group{0599, 0706, 1250, 1251, 1252, 1280}

Usage:

769C 01X
Caterpillar Products: All

Introduction

European Union Compliant, CE Marked

Important Safety Information




Illustration 1g02139237

Think Safety

Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.

Improper operation, lubrication, maintenance, or repair of this product can be dangerous and could result in injury or death.

Do not operate or perform any lubrication, maintenance, or repair on this product until you have read and understood the operation, lubrication, maintenance, and repair information.

Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons.

The hazards are identified by the Safety Alert Symbol and followed by a Signal Word such as "DANGER","WARNING", or "CAUTION". The Safety Alert "WARNING" label is shown below.

A non-exhaustive list of operations that may cause product damage are identified by "NOTICE" labels on the product and in this publication.

Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are therefore, not all inclusive. If a tool, procedure, work method, or operating technique that is not recommended by Caterpillar is used, the operator must be sure that the procedures are safe. The operator must also be sure that the product will not be damaged or made unsafe by any unspecified procedures.

The information, specifications, and illustrations in this publication are based on information that was available at the time that the publication was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other items can change at any time. These changes can affect the service that is given to the product. Obtain the complete and most current information before you start any job.

When replacement parts are required for this product, Caterpillar recommends using Cat replacement parts or parts with equivalent specifications including, but not limited to physical dimensions, type, strength, and material.

Literature Information

This manual contains safety information, operation instructions and maintenance information and should be stored with the tool group.

Some photographs or illustrations in this publication may show details that can be different from your service tool. Guards and covers might have been removed for illustrative purposes.

Continuing improvement and advancement of product design might have caused changes to your service tool, which are not included in this publication.

Whenever a question arises regarding your service tool or this publication, consult Dealer Service Tools (DST) for the latest available information.

Safety Section

The Safety Section lists basic safety precautions.

Read and understand the basic precautions listed in the Safety Section before operating or performing maintenance and repair on this service tool.

General Information Section

The General Information Section describes tooling functions and features. This section provides useful information on individual parts, additional tooling, and resources.

Operation Section

The Operation Section is a reference for the new operator and a refresher for the experienced operator.

Photographs and illustrations guide the operator through correct procedures for using the tool group.

Operating techniques outlined in this publication are basic. Skill and techniques develop as the operator gains knowledge of the service tool and tool capabilities.

Maintenance Section

The Maintenance Section is a guide to tool inspection, cleaning, storage, and tool disposal.

Safety Section

Safety Icon Nomenclature

Personal Protection/Important Information




Illustration 2g02166423

Personal Protection/Important Information

Hazard Avoidance


Crushing Hazard (foot)


Crushing Hazard (hand)


Pinch Point

Additional Contact Information

For additional product support questions concerning this tool, contact the Dealer Service Tools Hotline at:

USA: 800-542-8665, Option 1

International: 1-309-578-7372

E-mail: dealerservicetool_hotline@cat.com

Note: Continuing improvement and advancement of product design can mean some photographs or illustrations in this publication will show details that are different from your service tool.

398-9680 Calibration Test Group




Illustration 3g03366076

Table 1
Serviceable Parts    
Item     Part No.     Description    
1     398-9676     Hydrometer Instrument    
2     398-9677     Hydrometer Instrument    
3     398-9678     Beaker Instrument    
4     9U-7839     Stopwatch    
5     9U-7841     Viscosity Cup    
6     9U-7842     Beaker    
7     6V-9449     Case    

Table 2
Specifications    
Case     470 x 395 x 203 mm (18.5 x 15.6 x 8 in)    
Weight    
2.3 kg (5 lb)    
Viscosity Cup     Individually serialized (includes calibration sheets)    
Beaker Material     Nalgene or Pyrex    
NEEG3148 Decal     Also included (not shown)    

9U7840 Diesel Fuel and Fuel Injection Equipment Calibration Fluid Test Kit

Calibration Fluid Tests - Introduction

The quality and condition of the test fluid in fuel injection system test equipment will affect test results. Industry standards of J967D test fluid are tightly controlled for this reason. Checking fluid cleanliness, viscosity, and specific gravity are essential for accurate fuel system testing. The simplest way to verify that test fluid is within J967D specifications, is to monitor viscosity and specific gravity (density) on a regular basis. Filters should be replaced on a regular basis to ensure fluid quality.

Controlling viscosity is critical because internal leakage in pumps or nozzles will cause changes in delivery if the fluid is out of specification. In time the fluid will become diluted with diesel fuel and lube oil.

The 9U7841 Viscosity Cup is calibrated to measure the viscosity of J967D Calibration Fluid between the temperatures of 60 - 120 degrees F. Testing may be done on the fluid in the test stand reservoir before start-up, when the fluid is at room temperature, or on a beaker of fluid left standing at room temperature for a minimum of one hour. A constant thermometer reading is an indicator to proceed with the test.

Specific gravity is also an indicator of dilution.

Many factors affect the maintenance intervals. These include testing of used injection pumps, heat, or oil dilution. Other conditions that will require the replacement of the test fluid include visible contamination, color change, and increased foaming tendency.

Maintaining a constant fluid temperature during the test is critical.

Measuring SAE J967 Calibration Fluid Viscosity at Room Temperature Using the 9U7842 Beaker

Note: Before testing, wipe all instruments clean of any residue (packing foam, lint, etc.) that could restrict the cup orifice. Blow out the cup orifice with compressed air if required.

Note: Make and use copies of the Maintenance Record and Data Sheet contained in this book for your records.

Note: The charts included with this booklet are calibrated for a specific cup. The serial number of your cup must match that noted on your charts for proper test results. The charts in this booklet are for reference only.

  1. Draw a sample of fluid in the 9U-7841 Beaker (600 ml).

  1. Slowly submerge the 9U-7841 Cup into the fluid sample. The cup portion should be completely submerged. Place one of the hydrometers in the fluid sample next to the cup. This will be used as a thermometer only. Let these soak for at least 10 minutes do all of the pieces stabilize at the same temperature.

  1. When all temperatures have stabilized, remove the hydrometer and record the temperature.

  1. Holding the stop watch in one hand and the top of the handle in the other, raise the cup completely out of the fluid in a smooth rapid vertical motion. Keep the cup as level as possible

    Start the stop watch as soon as the top of the cup breaks the surface of the fluid. Hold the cup very steady for the first 10 seconds until the fluid level drops below the cup lip.

    Stop the watch as soon as the last drop of fluid completely drains through the hole on the inside of the cup.

  1. Record the temperature and elapsed time in seconds.

  1. Repeat steps 4 and 5 three times averaging the readings which should fall within one second of each other. Record the average elapsed time in seconds with temperature.

  1. Locate on the vertical axis of Chart I the average elapsed time obtained from step 6. Follow the value to the diagonal line. From this point drop down vertically to read the viscosity in Centistokes (mm2/sec). Record this viscosity.

  1. Locate the viscosity on the vertical axis of Chart II. Locate the measured temperature of the test fluid on the horizontal axis. If the point of intersection of these two values is between the upper and lower limit lines the fluid is satisfactory for continued use.

Measuring SAE J967 Calibration Fluid Viscosity at Elevated Temperatures or at the Sump

The fluid can be tested at the sump if desired. All required test equipment must be submerged in the sump until all temperatures are stabilized.

Measuring API Specific Gravity of SAE J967D Calibration Fluid




Illustration 4g03339356

Fill a 1P-7438 Beaker (1) about two-thirds full of the calibration fluid to be tested. Carefully lower the thermo-hydrometer (2) into the fluid. Push the thermo-hydrometer to below its float level, then allow it to float freely. Wait two or three minutes until the thermo-hydrometer is stationary so there are not air bubbles in the fluid, and the thermometer reading stabilizes.

Read the measured API gravity directly from the thermo-hydrometer. Use the scale on the narrow upper portion (A). To read the hydrometer scale, look at the fuel surface from slightly below the surface as shown in the left illustration. Then raise the eye slowly until this surface, which is first seen as an ellipse, becomes a straight line as shown in the right illustration. Read the API gravity number at the point this line cuts the hydrometer scale.

Record the observed API gravity. Record fluid temperature in degrees F, from the lower portion (B) of the thermo-hydrometer.

Note: If the fluid is not clear, read from above the surface and estimate as accurately as possible the point to which the fuel rises on the hydrometer scale.

Locate the intersection of the measured temperature and the measured specific gravity on Chart III. If the intersection is within the upper and lower limit, the fluid is okay. If the fluid is outside the limits, it should be discarded.




Illustration 5g03366126



Illustration 6g03361015



Illustration 7g03359570



Illustration 8g03359570



Illustration 9g03359573

Table 3
Data Sheet
   
Fiets Serial Number        
Tested By:        
Date:        
Comments:    

Table 4
Viscosity Test     Measured Temp F°     Elapsed TimeSeconds    
Test 1            
Test 2            
Test 3            
Average            
           
Viscosity         Centistokes    
Viscosity Test Results     Pass     Fail    

Table 5
Specific Gravity Test    
Measured Temp_____________°F    
Measured API Gravity:    
Specific Gravity Test Results:     Pass     Fail    
Visual Check:    
   

Measuring Diesel Fuel API Gravity

Introduction

Many complaints of lack of power from diesel engines can be traced to a light grade of diesel fuel. Power obtained from diesel fuel is determined by its BTU content, which is in direct relation to its weight per gallon. By simply measuring the API (American Petroleum Institute) gravity of the fuel, the performance of the engine can be compared with the factory horsepower ratings. The horsepower ratings of diesel engines as listed in the Cat Rack Setting Information were obtained with fuel having an API gravity of 35° at 60°F. If a fuel with a high API gravity is used (lighter in pounds per gallon), the power output from the engine will be lower than listed because there is less heat value per unit volume of fuel.

Measuring API Gravity of Diesel Fuel

1P7408 Thermo-hydrometer has a range of 29° 41° API.

5P2712 Thermo-hydrometer has a range of 39° - 51° API.




Illustration 10g03359597

Fill a 1P7438 Beaker (1) about two-thirds full of the diesel fuel to be tested. Carefully lower the thermo-hydrometer (2) into the fuel. Push the thermo-hydrometer to below its float level, then allow it to float freely. Wait two or three minutes until the thermo-hydrometer is stationary so there are no air bubbles in the fuel, and the thermometer reading stabilizes.

Read the measured API gravity directly from the thermo-hydrometer. Use the scale on the narrow upper portion (A). To read the hydrometer scale, look at the fuel surface from slightly below the surface as shown in the left illustration. Then raise the eye slowly until this surface, which is first seen as an ellipse, becomes a straight line as shown in the right illustration. Read the API gravity number at the point this line cuts the hydrometer scale.

Record the observed API gravity to the nearest full degree of API. For example, read 40.4° as 40° API. Record fuel temperature in degrees F, from the lower portion (B) of the thermo-hydrometer. Do not use the right scale of the thermometer.

Note: If the fuel is not clear, read from above the surface and estimate as accurately as possible the point to which the fuel rises on the hydrometer scale.




Illustration 11g03359557

Table of Horsepower Correction Factors

Table 6
Corrected API Gravity at 60° F
   
Pre-combustion Chamber Engines
   
Direct Injection Engines (Use the correct full load RPM)






   
1800 2000     2200     2400     2600     2800     3000     3200    
32.0
32.5
33.0
33.5
34.0    
.984
.987
.990
.992
.995    
.986
.988
.990
.992
.995    
.986
.988
.990
.992
.995    
.986
.988
.990
.992
.995    
.986
.988
.990
.992
.995    
.986
.988
.990
.992
.995    
.986
.988
.990
.992
.995    
.986
.988
.990
.992
.995    
.986
.988
.990
.992
.995    
34.5
35.0
35.5
36.0
36.5    
.997
1.000
1.003
1.005
1.008    
.998
1.000
1.003
1.007
1.013    
.998
1.000
1.003
1.007
1.010    
.998
1.000
1.003
1.007
1.011    
.998
1.000
1.003
1.007
1.011    
.998
1.000
1.003
1.007
1.011    
.998
1.000
1.003
1.008
1.012    
.998
1.000
1.003
1.008
1.012    
.998
1.000
1.003
1.008
1.012    
37.0
37.5
38.0
38.5
39.0    
1.011
1.014
1.017
1.020
1.023    
1.014
1.018
1.022
1.025
1.029    
1.014
1.018
1.022
1.026
1.030    
1.014
1.018
1.022
1.026
1.030    
1.015
1.019
1.022
1.026
1.030    
1.015
1.019
1.023
1.027
1.031    
1.016
1.020
1.024
1.028
1.032    
1.016
1.020
1.024
1.028
1.033    
1.016
1.021
1.025
1.029
1.034    
39.5
40.0
40.5
41.0
41.5    
1.027
1.030
1.034
1.038
1.043    
1.034
1.038
1.043
1.048
1.053    
1.034
1.038
1.043
1.048
1.054    
1.034
1.039
1.044
1.049
1.055    
1.035
1.040
1.045
1.050
1.056    
1.036
1.040
1.045
1.051
1.056    
1.036
1.041
1.046
1.051
1.057    
1.037
1.042
1.047
1.053
1.059    
1.039
1.045
1.051
1.057
1.064    
42.0
42.5
43.0
43.5
44.0    
1.047
1.053
1.060
1.067
1.076    
1.059
1.066
1.073
1.082
1.095    
1.060
1.067
1.074
1.084
1.096    
1.061
1.068
1.076
1.085
1.098    
1.062
1.069
1.077
1.086
1.099    
1.063
1.070
1.078
1.087
1.100    
1.064
1.071
1.079
1.088
1.102    
1.066
1.072
1.081
1.091
1.105    
1.072
1.080
1.089
1.099
1.115    

Use the above chart to find the horsepower correction factor.

Calculating the Corrected Horsepower

  1. Determine the Rated (full load) horsepower from the Rack Setting Information Book.

  1. Divide the rated horsepower by the horsepower correction factor for fuel density: the result is the corrected horsepower.

    Example: 1674 Truck Engine Serial No. 94B2551.Rated Horsepower: 270 Horsepower

Calculations:

  1. Measured API gravity: 40.4° API at 50° (round to 40° API

  1. Corrected API gravity (see chart): 41°API at 60°F

  1. Horsepower correction factor (see chart): 1.038

  1. Corrected Horsepower = Rated Horsepower divided by Correction Factor = 270 divided by 1.038 = 260 Horsepower (or 3.75% horsepower loss)

Correcting for Fuel Density When Testing Engines on a Dynamometer

When engines are tested on a dynamometer which measures actual flywheel or drive train output, the observed horsepower is dependent on the fuel used. If the fuel being used in not 35° API at 60°F, then any dynamometer readings must be corrected to determine the output if 35°API fuel had not been used. The same horsepower correction factor is used, but the formula is different.

Corrected Horsepower = Observed Horsepower x Horsepower Correction Factor

Example:

1674 Truck Engine, Serial No. 94B2551

Rated (full load Horsepower: 270 Horsepower)

Observed (dynamometer) Horsepower: 260 Horsepower

Calculations:

  1. Measured API gravity: 39.6° API at 50°F (round to 40° API)

  1. Corrected API Gravity (see chart): 41° API at 60°F

  1. Horsepower Correction Factor (see chart): 1.038

  1. Corrected Horsepower= Observed Horsepower x Horsepower Correction Factor 260 Horsepower x 1.038 = 270 Horsepower

(Although the dynamometer indicated low Horsepower, if the proper fuel had been used, the engine would be operating at rated output. The factory tolerance on rated engine output is ± 3%.)

For more information on dynamometer testing diesel engines, see Special Instruction Form GEG01024.

Diesel Fuel API Gravity to lbs./US gallon or kg/liter Conversion Chart

The following chart may be used to convert the fuel API gravity to lbs/US gallon or kg/liter. These weights are for reference and are to be used when evaluating engine performance. Measurement of fuel flow rates cn be converted to horsepower (using full load brake-specific fuel consumption, BSFC, values).

Table 7
Fuel API Gravity     Specific Weight    
lbs/US Gallon kg/liter    
32
33
34    
7.206
7.163
7.119    
0.8654
0.8602
0.8550    
35
36
37    
7.076
7.034
6.993    
0.8498
0.8448
0.8398    
38
39
40    
6.951
6.910
6.870    
0.8348
0.8299
0.8251    
41
42
43
44    
6.830
6.790
6.752
6.713    
0.8203
0.8155
0.8109
0.8063    

All of the above measurements are taken at 60° F (15° C)

Caterpillar Information System:

2013/01/21 Software Update For Proper Air Fuel Ratio Controller Operation Of Certain G3408 and G3412 Engines {1901, 1920}
2013/01/21 New Fuel Pressure Regulator and Set Screw Are Used for 3600 and C280 Engines {1252, 1254}
C9.3 Industrial Engine Fumes Disposal Filter Element - Replace - Emission Related Component
C3.3B Engines for Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
C3.3B Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
C3.3B Engines for Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
C3.3B Engines for Caterpillar Built Machines Boost Pressure Sensor - Remove and Install
C32 Marine Generator Set Control Panel - Marine Generator Set Engine Control Panel 3 (MGECP 3)
Air Shutoff Test and Inspection for Certain C7 and C9 Petroleum Engines{1078} Air Shutoff Test and Inspection for Certain C7 and C9 Petroleum Engines{1078}
2013/03/29 New Engine Oil Hoses Are Used on Certain Excavators Equipped with C13 Engines {1308}
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000} Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
C32 Auxiliary Engine Belts - Inspect/Adjust/Replace
C175-16 Marine Propulsion Engines Engine Shutdown Occurrence
C3.3B Engines for Caterpillar Built Machines Cylinder Head - Remove and Install
2013/02/06 Different Water Temperature Regulators (Thermostats) are Available for G3600 Engines {1355}
C3.3B Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
C3.3B Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C32 Marine Generator Set Safety Messages
C32 Marine Generator Set Model View Illustrations
3516C Locomotive Engine and Generator Set Maintenance Interval Schedule
2013/01/29 Improved Software is Now Used for Petroleum Fracturing Transmissions {7620}
2013/03/01 New Suction Screen and Handle Are Used in 3500 Locomotive Engines {1302, 1302}
Work Area Vision System Maintenance Interval Schedule
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.