Seat Maintenance Interval Schedule
在进行任何操作或保养步骤之前,确保阅读并理解所有的安全信息、警告和说明。
用户对保养行为负责。 保养工作包括所有调整、使用正确的润滑剂和更换正常磨损和老化的部件。 未能遵照正确的保养周期和步骤可能导致产品性能降低和/或部件磨损加速。
根据里程数、工作小时数或日历时间(以先到者为准)确定保养周期。 在恶劣作业条件下工作的产品可能需要更频密的保养。
注: 在进行每个连续的周期的保养之前,必须先进行前一个周期的所有保养。
Show/hide table
需要时即进行的保养     | 每 1000 个工作小时或 6 个月     |
座垫 - 清洁/更换     | 悬架轴承 - 检查/润滑     |
座椅扶手垫(如有配备) - 清洁/更换     | 悬架可调减振器(如有配备)拉索 - 检查调整     |
每 10 个工作小时或每天     | 悬架乘坐区指示器 - 检查功能     |
座椅安全带 - 检查     | 每 2000 个工作小时或 1 年     |
最初 250 个工作小时     | 座垫 - 检查     |
滑块 - 检查调整     | 座椅靠背盘枢轴螺母 - 检查拧紧程度     |
前/后止动螺栓 - 检查拧紧程度     | 座椅扶手(如有配备)垫 - 检查     |
控制装置 - 检查功能     | 座椅扶手(如有配备)枢轴螺栓 - 检查拧紧程度     |
悬架减振器 - 检查     | 悬架减振器 - 检查     |
悬架空气弹簧、软管、阀 - 检查     | 悬架缓冲器 - 检查     |
悬架缓冲器 - 检查     | 悬架栓系 - 检查     |
最初 500 个工作小时     | 安装日期之后的每 3 年 (1)     |
滑块 - 检查调整     | 座椅安全带 – 更换     |
前/后止动螺栓 - 检查拧紧程度     | 每 5000 个工作小时或 4 年     |
控制装置 - 检查功能     | 滑块 - 检查/更换     |
座垫 - 检查     | 悬架减振器 - 检查/更换     |
座椅靠背盘枢轴螺母 - 检查拧紧程度     | 悬架空气弹簧 - 检查/更换     |
座椅扶手(如有配备)枢轴螺栓 - 检查拧紧程度     | 悬架缓冲器 - 检查/更换     |
悬架减振器 - 检查     | 悬架轴承 - 检查/更换     |
悬架空气弹簧、软管、阀 - 检查     | 悬架栓系 - 更换     |
悬架缓冲器 - 检查     | 每 10000 个工作小时或 8 年     |
悬架乘坐区指示器 - 检查功能     | 整套座椅(座椅加悬架)- 检查/更换     |
每 500 个工作小时或 3 个月     | -     |
滑块 - 检查调整     | |
前/后止动螺栓 - 检查拧紧程度     | |
控制装置 - 检查功能     |
Show/hide table
( 1 ) | 软管无法确定安装日期,则使用座椅安全带制造日期。 |
Caterpillar Information System:
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Pistons and Connecting Rods - Assemble
C7.1 Industrial Engine Pistons and Connecting Rods - Disassemble
C7.1 Industrial Engine Pistons and Connecting Rods - Remove
C7.1 Industrial Engine Piston Cooling Jets - Remove and Install
C7.1 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Pilot Oil) - Remove and Install
C7.1 Industrial Engine Camshaft Bearings - Remove and Install
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install
CB44B Vibratory Asphalt Compactor Propel System Piston Pump Neutral - Test and Adjust - Mechanical , Split Drum
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Disc Saw) - Remove and Install