Cylinder Head
Show/hide table
| |
| Illustration 1 | g03130536 |
|
Typical example | |
Show/hide table
| Specification for 206-1558 Cylinder Head Gp, 248-5030 Cylinder Head Gp, 378-7413 Cylinder Head Gp, and 378-7416 Cylinder Head Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 5B-7890 Pipe Plug | Before assembly, apply Loctite C5A copper anti-seize to the threads. |
| 2 | 6 | 131-0420 Cylinder Head Fastener Gp | Before assembly, apply engine oil to cylinder head bolt threads.
Use the following procedure in order to tighten the cylinder head bolts. Refer to Illustration1 for the tightening sequence: 1. Tighten bolt (1) through bolt (8) in the numerical sequence to 2. Again tighten bolt (1) through bolt (8) in the numerical sequence to 3. Again tighten bolt (1) through bolt (8) in the numerical sequence to 4. Tighten two bolts (4) only after bolt 1 through bolt 8 have been given the final torque. Tighten two bolts (4) to |
| 3 | 2 | 131-0421 Cylinder Head Fastener Gp | |
| 4 | 2 | 5B-0213 Bolt | |
Show/hide table
| |
| Illustration 2 | g03130499 |
Show/hide table
| Item | Qty | Part | Specification Description |
| 5 | 5 | 3B-0645 Cup Plug | Apply high strength or high temperature anaerobic flange sealant to the bores for the cup plugs prior to the installation. |
| 6 | 3 | 3B-0623 Cup Plug | Apply high strength or high temperature anaerobic flange sealant to the bores for the cup plugs prior to the installation.
Installation depth (F) is |
| 7 | 2 | 191-6760 Valve Seat Insert | During installation, shrunk the valve seat insert with reduced temperature. |
| 8 | 1 | 4P-6925 Oil Sleeve | During installation, shrunk the oil sleeve with reduced temperature.
Installation depth is |
| 9 | 2 | 257-9166 Valve Seat Insert | During installation, shrunk the valve seat insert with reduced temperature. |
| E | 2 | 3B-0623 Cup Plug | Installation depth of the cup plugs from the top surface of the cylinder head is |
Caterpillar Information System:
C9.3 Tier 4 Final Engines Fuel Injection Pump
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Replace
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Configure
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Symptom Troubleshooting
2012/07/19 Improved Flame Arrestors Are Used for Certain G3500E Engines {1071, 1092}
CEM Locomotive Aftertreatment Catalyst (DOC) - Replace
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Cat Data Link - Test
G3500 Engines Cylinder Head
C13 Tier 4 Final Engines Solenoid Valve
2012/10/04 A New Rocker Arm Assembly Is Used in Certain C11 and C13 Commercial Engines {1123}
Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254} Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254}
UPS 250 and UPS 300 Uninterruptible Power Supplies Using Computer Software
G3500 Engines Cylinder Head
C7.1 Industrial Engine Fuel Filter (In-Line) - Replace
793F Off-Highway Truck Engine Supplement Turbocharger - Remove and Install - High Altitude
C32 Marine Engines Unit Injector Sleeve - Remove
C32 Marine Engines Unit Injector Sleeve - Install
G3500 Engines Cylinder Head
C7.1 Industrial Engine Maintenance Interval Schedule
C9.3 Industrial Engine Turbocharger
C6.6 Industrial Engine Engine Crankcase Breather Element - Replace
C4.4 Industrial Engine Fuel System Primary Filter (Water Separator) Element - Replace
C4.4 Industrial Engine Fuel System Primary Filter/Water Separator - Drain
C4.4 Industrial Engine Fuel System Secondary Filter - Replace