Camshaft
Show/hide table
Illustration 1 | g03123976 |
Typical example (1) Left-hand camshaft assembly (2) Right-hand camshaft assembly |
Show/hide table
Specification for 4P-8337 Camshaft Gp and 382-5092 Camshaft Gp | |||
Item | Qty | Part | Specification Description |
A | - | - | Thickness of the groove in a new camshaft assembly is |
C | 1 | 5B-5821 Dowel | Extension of the dowel is |
D | 2 | 4N-1650 Dowel | Extension of the dowel is |
E | 2 | 7N-3218 Thrust Washer | Thickness of a new thrust washer is |
F | - | - | Diameter of bearing journals in a new journal camshaft assembly is |
Bore in camshaft bearing after installation is |
|||
- | - | - | End play for a new camshaft assembly is |
3 | 16 | 5P-0076 Bolt | Torque to |
Show/hide table
Illustration 2 | g03123978 |
Show/hide table
Item | Qty | Part | Specification Description |
- | - | - | Use the following procedure in order to determine the camshaft lobe lift: |
1. Measure camshaft lobe height (H). | |||
2. Measure base circle (J). | |||
3. Subtract the base circle (J) from the camshaft lobe height (H). The difference is the actual camshaft lobe lift. | |||
G | - | - | Specified camshaft lobe lift: |
Inlet lobe is |
|||
Exhaust lobe is |
Caterpillar Information System:
C13 Tier 4 Final Engines Engine Support (Front)
C13, C15, and C18 Tier 4 Final Engines Water Lines
G3500B Engines Cylinder Block
CEM Locomotive Aftertreatment Product Storage
Procedure for Testing the Vacuum Pump On Certain Uninterruptible Power Supply{4287} Procedure for Testing the Vacuum Pump On Certain Uninterruptible Power Supply{4287}
C4.4 Engines for Caterpillar Built Machines Piston and Rings
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Data Link
2012/07/06 A New Fan Guard Is Now Used on Certain C27 and C32 Engines {1353}
3500B Generator Set Engines Engine Oil Lines
3500B and 3500C Marine Engines Camshaft
Procedure to Change Parameter Settings for Battery Voltage Regulation on Certain Uninterruptible Power Supply{7451} Procedure to Change Parameter Settings for Battery Voltage Regulation on Certain Uninterruptible Power Supply{7451}
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Output Components
C7.1 Engines for Caterpillar Built Machines Starter Motor
C7.1 Engines for Caterpillar Built Machines Alternator
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Diagnostic Trouble Codes
UPS 250 and UPS 300 Uninterruptible Power Supplies General Hazard Information
C7.1 Industrial Engine Flexible Exhaust Pipe
C18 Marine Engines Heat Exchanger - Disassemble
Alignment Procedure for Certain G3500 Generator Set Engines with Gearbox {7002} Alignment Procedure for Certain G3500 Generator Set Engines with Gearbox {7002}
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Solenoid Valve - Test
C9.3 Tier 4 Final Engines Electric Starting Motor
C9.3 Tier 4 Final Engines Flywheel
UPS 250 and UPS 300 Uninterruptible Power Supplies Device Bus Network
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Event Codes