Engine Oil Filter
Show/hide table
Illustration 1 | g03051196 |
Right side view |
Show/hide table
Specification for 215-9667 Engine Oil Filter Gp | |||
Item | Qty | Part | Specification Description |
1 | 2 | 6B-9202 Spring | Length under test force is Test force is Free length after test is |
2 | 2 | 7N-7697 Plunger | Cooling jet sequence valves must start to open at a pressure difference of Cooling jet sequence valves must be fully open at a pressure difference of |
3 | 3 | 275-2604 Engine Oil Filter | Apply clean engine oil to the sealing surface of the filter element. Screw the filter element onto the mounting base until the sealing surface contacts the base. Then tighten the filter element for an additional one full turn (360 degrees). |
4 | 1 | 109-2332 O-Ring Seal | Before assembly, lubricate the bore lightly with the lubricant that is being sealed. |
5 | 1 | 2W-1053 Plug | Torque to |
6 | 1 | 6V-5048 O-Ring Seal | Before assembly, lubricate the bore lightly with the lubricant that is being sealed. |
7 | 3 | 7G-6713 Spring | Length under test force is Test force is Free length after test is |
8 | 3 | 1P-1367 Plunger | Bypass valve must start to open at a pressure difference of The plunger must move freely in the bore. |
Show/hide table
Illustration 2 | g03045505 |
Rear view |
Show/hide table
Illustration 3 | g03045506 |
Show/hide table
Item | Qty | Part | Specification Description |
9 | 3 | 109-2332 O-Ring Seal | Before assembly, lubricate the bores lightly with the lubricant that is being sealed. |
Caterpillar Information System:
G3516C and G3516E Gas Engines Water Pump
C7.1 Industrial Engine Product Description - Engine and Aftertreatment
G3512E Generator Set Engines Engine Oil Pan
2012/05/23 Activation Password Is Now Required For Touchscreens Of Uninterruptible Power Supplies {7451}
G3500 Generator Sets Fluid Recommendations
3512C and 3516C Marine Propulsion Engines Speed Control - Test
2012/05/21 New Clamping for the Jacket Water Bypass Tube on Certain 3500 Engines {1380, 7553}
C18 Marine Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C18 Marine Engines Inlet and Exhaust Valve Guides - Remove and Install
2012/05/21 Viewing the Electronic Thermostat Position via ET on C175 Engines {135V, 7610}
C18 Marine Engines Inlet and Exhaust Valves - Remove and Install
C18 Marine Engines Inlet and Exhaust Valve Springs - Remove and Install
3516B Engine for the MT4400D Off-Highway Truck Flywheel
G3500 Generator Sets Coolant (DEAC) - Change
C9.3 Tier 4 Final Engines Sensor Signal (Analog, Active) - Test
G3500 Generator Sets Coolant (NGEC) - Change
3516B Engine for the MT4400D Off-Highway Truck Auxiliary Drive (Lower Left Hand)
14M Series 3 Motor Grader Brakes, Indicators and Gauges - Test
G3500 Generator Sets Coolant Level - Check
2012/05/21 Cat® Electronic Technician (Cat® ET) Improved for Configuring of Annunciator Alarm Module on Certain Cat® Products {0785, 7400}
C18 Marine Engines Engine Oil Filter Base - Remove and Install
3516B Engine for the MT4400D Off-Highway Truck Accessory Drive - Air Conditioner Compressor
C7.1 Industrial Engine Plate Locations and Film Locations - Aftertreatment System
G3500 Generator Sets Coolant Sample (Level 2) - Obtain