Water Pump
Show/hide table
| |
| Illustration 1 | g03045437 |
Show/hide table
| Specification for 253-0585 Water Pump Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 3J-7354 O-Ring Seal | Lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
| 2 | 1 | 5H-6734 O-Ring Seal | Lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
| 3 | 1 | 3D-2824 O-Ring Seal | Lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
Show/hide table
| |
| Illustration 2 | g03045418 |
Show/hide table
| Item | Qty | Part | Specification Description |
| 4 | 1 | 259-4596 O-Ring Seal | Lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
| 5 | 1 | 229-5469 Bearing Locknut | Torque to Tighten the set screw to |
| 6 | 1 | 258-8726 Pump Shaft | Lubricate the shaft with a thin film of clean engine oil before pressing the impeller onto the shaft. The end of the shaft must be flush with the face of the impeller within Diameter of the shaft to the impeller seating is |
| Note: Improper handling can damage the ceramic seal. If the shaft is bumped during installation, the ceramic seal that is internal to the pump may crack leading to a coolant leak from the weep hole. Caution should be taken during installation not to make hard contact to the shaft. Insert the pump completely during installation. Do not allow the shaft to support the weight of the pump during installation. | |||
| 7 | 1 | 235-4643 Water Pump Seal | Use the following procedure in order to install the water pump seal:
1. Install the seal dry. 2. Install the seal within 2 minutes of the removal of the seal from the shipping sleeve. 3. Install the seal by using a slow motion and even motion. 4. Use the correct installation tool. |
| Minimum leakage per minute for the lip type seal at |
|||
| 8 | 1 | 336-2212 Water Pump Seal As | Use the following procedure in order to install the seal group:
1. Use 207-1600 Rubber Lubricant in order to aid in assembly. 2. Use the installation tool and hand pressure to seat the ceramic ring and the rubber seal in the pump housing. 3. Remove the spring from the seal assembly. 4. Use the installation tool and hand pressure to press the seal assembly on the shaft until the seal faces make light contact. 5. Install the spring. |
| Minimum leakage per minute for the water pump seal assembly at |
|||
| 9 | 1 | 313-2760 Impeller | Bore of the impeller for new shaft is |
Caterpillar Information System:
C7.1 Industrial Engine Product Description - Engine and Aftertreatment
G3512E Generator Set Engines Engine Oil Pan
2012/05/23 Activation Password Is Now Required For Touchscreens Of Uninterruptible Power Supplies {7451}
G3500 Generator Sets Fluid Recommendations
3512C and 3516C Marine Propulsion Engines Speed Control - Test
2012/05/21 New Clamping for the Jacket Water Bypass Tube on Certain 3500 Engines {1380, 7553}
C18 Marine Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C18 Marine Engines Inlet and Exhaust Valve Guides - Remove and Install
2012/05/21 Viewing the Electronic Thermostat Position via ET on C175 Engines {135V, 7610}
C18 Marine Engines Inlet and Exhaust Valves - Remove and Install
C18 Marine Engines Inlet and Exhaust Valve Springs - Remove and Install
G3516C and G3516E Gas Engines Camshaft Bearing Position
G3500 Engines Engine Oil Filter
3516B Engine for the MT4400D Off-Highway Truck Flywheel
G3500 Generator Sets Coolant (DEAC) - Change
C9.3 Tier 4 Final Engines Sensor Signal (Analog, Active) - Test
G3500 Generator Sets Coolant (NGEC) - Change
3516B Engine for the MT4400D Off-Highway Truck Auxiliary Drive (Lower Left Hand)
14M Series 3 Motor Grader Brakes, Indicators and Gauges - Test
G3500 Generator Sets Coolant Level - Check
2012/05/21 Cat® Electronic Technician (Cat® ET) Improved for Configuring of Annunciator Alarm Module on Certain Cat® Products {0785, 7400}
C18 Marine Engines Engine Oil Filter Base - Remove and Install
3516B Engine for the MT4400D Off-Highway Truck Accessory Drive - Air Conditioner Compressor
C7.1 Industrial Engine Plate Locations and Film Locations - Aftertreatment System