G3516C and G3516E Gas Engines Caterpillar


Exhaust Manifold

Usage:

G3516C F6D


Illustration 1g03032117

Table 1
Specification for 210-7753 Exhaust Manifold Gp 
Item  Qty  Part  Specification Description 
Before assembly, apply Loctite nickel anti seize to the washer surface and to the threads of the bolts. 
162-6466 Bolt  Torque to 240 ± 40 N·m (177 ± 30 lb ft)
64  9L-7373 High Temperature Bolt  Use the following procedure in order to tighten the bolts:
1. Torque the bolts to 55 ± 5 N·m (41 ± 4 lb ft).
2. Again, tighten the bolts to 55 ± 5 N·m (41 ± 4 lb ft)
16  200-6554 Bellows As  Install bellows assemblies with the flow direction, as shown in the Illustration 1. 
Allowable offset for the bellows assemblies from the center of the casting inner diameter is 1.5 mm (0.06 inch).
9X-2068 High Temperature Bolt  Torque to 50 ± 10 N·m (37 ± 7 lb ft)
38  437-7470 Bolt  Use the following procedure in order to tighten the clamps:
1. Torque the clamp bolts to 25 ± 6 N·m (221 ± 53 lb in).
2. Lightly tap around the clamps.
2. Again, tighten the clamp bolts to 25 ± 6 N·m (221 ± 53 lb in)
7L-6443 High Temperature Bolt  Torque to 50 ± 10 N·m (37 ± 7 lb ft)

Caterpillar Information System:

2012/06/25 Obsolete Merlin Gerin CK and CM Frame Circuit Breaker Replacements Are Now Available {1420, 4461}
C9.3 Tier 4 Final Engines Event Codes
C9.3 Tier 4 Final Engines Diagnostic Trouble Codes
2012/05/14 New Flash Files Are Available for Certain Engines {1901, 1920}
C3.3B and C3.8 Engines for Caterpillar Built Machines Oil Pressure Is Low
C32 Marine Engines Coolant Level Sensor - Remove and Install
2012/05/07 A Procedure to Check Ash Build-up Within the Diesel Particulate Filter (DPF) Is Now Available {108F}
C175-16 Generator Set Refill Capacities
C7.1-XQ230 Rental Generator Set Setup
Inspection and Salvage of Front Wheel Spindles for Off-Highway Trucks {4201, 4205} Inspection and Salvage of Front Wheel Spindles for Off-Highway Trucks {4201, 4205}
C15 and C18 Tier 4 Final Engines DEF Dosing Control System
2012/05/07 An Improved Guide Spring and Valve Lifter Assembly Are Available in Certain C9 ACERT Engines {1209}
C9.3 Tier 4 Final Engines Engine Cranks but Does Not Start
325 VM and VH Variable Gauge Undercarriage Final Drive - Disassemble
C32 Marine Engines Engine Oil Pressure Sensor - Remove and Install
2012/08/03 New Thermostats Are Now Used for Jacket Water Heater on Certain Cat Gensets and Cat Engines {1383}
C175-16 Engine for 795F Series AC Off-Highway Trucks Housing (Front)
2012/07/23 New Software Is Used for Certain G3516C Engines {1901, 1920}
C9.3 Tier 4 Final Engines Fuel Consumption Is Excessive
C9.3 Tier 4 Final Engines Fuel Pressure Is High
C13, C15, and C18 Tier 4 Final Engines Fuel Pressure Is Low
C9.3 Tier 4 Final Engines Fuel Temperature Is High
C9.3 Tier 4 Final Engines Oil Contains Fuel
C32 Marine Engines Fuel Pressure Sensor - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.