Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}
- Caterpillar Products:
- All
Show/hide table
Illustration 1 | g03012597 |
Example of a bolt with a black coating that is a poor electrical conductor |
To minimize damage from rust and corrosion, many fasteners have black coatings that resist electrical conductivity in addition to resisting corrosion. Do not use such fasteners for electrical terminals or electrical grounding.
Fasteners that provide good electrical conductivity have silver-colored zinc plating.
Direct contact between terminals or a terminal-to-ground boss is recommended. Refer to Illustration 2
Show/hide table
Illustration 2 | g03012656 |
(1) Stud (2) Nut (3) Washer (4) Ring terminal (5) Boss |
Table 1 lists some nuts and washers that are commonly used for electrical grounds. The low torque is recommended so that the ring terminals are not damaged.
Show/hide table
Fastener     | Size     | Low Torque     |
5C-2890 Nut     | M6     | 6 ± 1 N·m (53 ± 8 lb in)     |
1A-8912 Washer     | ||
5C-7261 Nut     | M8     | 15 ± 3 N·m (11 ± 2 lb ft)     |
8F-7242 Washer     | ||
8T-4133 Nut     | M10     | 30 ± 7 N·m (22 ± 5 lb ft)     |
7P-1695 Washer     | ||
8T-4244 Nut     | M12     | 50 ± 10 N·m (37 ± 7 lb ft)     |
4B-4280 Washer     |
Caterpillar Information System:
3512C and 3516C Marine Engines Engine Oil Lines
CX48-P2300 Petroleum Transmission Transfer Gears - Remove and Install - Upper
Remanufactured Cylinder Packs Contain Improperly Installed Piston Rings for Certain Caterpillar Products{1215, 1239} Remanufactured Cylinder Packs Contain Improperly Installed Piston Rings for Certain Caterpillar Products{1215, 1239}
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove - Through Flow Diesel Particulate Filter
C3.4B Engines for Caterpillar Built Machines Cylinder Head - Remove
C3.4B Engines for Caterpillar Built Machines Cylinder Head - Install
2012/08/10 A New Turbocharger Housing is Used on Certain 3512B Engines {1052, 1065}
G3516C and G3516E Gas Engines Junction Box
C3.4B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C3.4B Engines for Caterpillar Built Machines Water Pump - Remove
C3.4B Engines for Caterpillar Built Machines Water Pump - Install
C3.4B Engines for Caterpillar Built Machines Wastegate Solenoid - Remove and Install
CX48-P2300 Petroleum Transmission Control Manifold - Disassemble
3500C Marine Engines Engine Oil Filter
G3516 Engines Engine Oil Pump
2012/04/30 New Software Is Now Used for Certain Tier 4 Interim Commercial Engines {1920}
2012/04/24 Turbocharger Surge on Certain G3500C and G3500E Engines that are Equipped with Dual Turbochargers {1052}
2012/04/30 Improved Fuel Injector O-Ring Seals Are Used on Certain Machine Engines {1251, 1290}
2012/04/30 Improved Fuel Injector O-Ring Seals Are Used on Certain Commercial Engines {1251, 1290}
3500C Marine Engines Engine Oil Sump Pump
3512C and 3516C Marine Engines Coolant Level Switch
3500C Marine Engines Engine Oil Sump Pump
Water Temperature Regulator on Certain C6.6 and C4.4 Engines{1355, 1380} Water Temperature Regulator on Certain C6.6 and C4.4 Engines{1355, 1380}
3512C and 3516C Marine Engines Crankshaft